Diagnostics and repair
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
The care journal
Care routines, fixes and code explanations built from the manuals Maytag published and matched to the models they cover.

Where the water sits tells you what to do. A little in the dispenser area is normal, and more than half an inch after a thorough drawer cleaning is a service call. Water under the door seal usually means trapped lint, hair or small items, so clean the bellows monthly. Water in the tub with wet clothes points to an unbalanced load or a low spin, and Drain and Spin fixes that. [1][2][3][4]

A Maytag top-load washer that stops agitating or spinning is most often reacting to the load or the setup, not to a broken part. Check balance, the cycle choice, the drain hose and standpipe, the level of the cabinet, a recent power cut, and anything resting on or under the lid. If dU or LdL stays on after that, book a technician. [1][2][3][4]

When a Maytag electric dryer tumbles with no heat, check the household supply before the machine: both breakers of its 30-amp, 240-volt circuit, the power cord and the terminal screws. An L2 or F4 E4 code points the same way, and a five-minute breaker reset is the step Maytag gives. F4 E1 names the heater or its relays and uses a one-minute reset. [1][2][3][4]

After a power cut, a Maytag electric range may show F9 or F9 E0 because of noise on the line. Cut the range's breaker for 60 seconds, restore it, and watch for 60 more. If F9 stays, the outlet may be miswired and an electrician should check the supply. If nothing shows at all, check the breaker or fuse, then the lock, demo and delay settings. [1][2][3]

Water near a Maytag French-door refrigerator usually comes from one of four places: the dispenser (a short pour or full drip tray), the filter (loose seating or overdue), the ice chute (melting shavings) or the supply connection behind the cabinet. Check each in that order, and leave a leaking filter out to run the system in bypass until you have a new one. [1][2][3][4]

To winterize a Maytag washer, close both faucets, detach and empty the inlet hoses, pour 1 quart of R.V.-type antifreeze into the basket, run RINSE & SPIN for about 30 seconds, then unplug it. To move a front-loader, also bundle the hoses and cord inside the drum and use new transport bolts. To restart, flush the lines and run a cleaning cycle with half the detergent. [1][2][3]

Change a Maytag refrigerator water filter twice a year, when its light asks, or sooner if the dispenser slows or the ice shrinks. With no light, Maytag's pages say every 6 months on one page and every 6 to 9 months on another, with an earlier change if flow drops. A clogged filter can stay out in bypass mode, unfiltered, until you fit a new one. [1][2][3]

AquaLift loosens soil with low heat and water; it does not remove everything. On an AquaLift Maytag range, start with a cool, empty, level oven, pour in 2 cups of filtered or distilled water, press AQUALIFT SELF CLEAN then START, allow about 40 minutes, then wipe out the softened soil with a non-scratch sponge. Run it again for stubborn spots, and never use oven cleaners. [1][2][3]

Water at a Maytag dishwasher usually comes from steam at the door vent, suds, a pre-washed or soaked load, an item caught in the door seal, an unlevel or out-of-square tub, or a loose supply or drain connection. Check those first. Water in the drip tray, which goes with an F8E4 code, must be emptied, and the supply shut off if the code appears. [1][2][3]

A Maytag freezer's temperature alarm buzzes when the inside is 10°F (-12°C) or more above the normal level for its setting, and a three-position switch tests, enables or silences it. On a chest freezer, green means the compressor is running and red means the temperature is not low enough, which a big food load, a warm location or a lid left open often explains. [1][2][4][5]

Maytag asks for a power cycle after many washer, dryer and dishwasher codes, and the wait differs: 5 minutes unplugged for a washer, 30 seconds for a dishwasher, and 1 or 5 minutes at the breaker for a dryer, depending on the code. Restore power, run a cycle and watch the display. [1][4][5][8]

PUSH, Lo, Pre, LOC, 12:00 or POWER LOSS, Demo Mode and Sabbath are messages Maytag's range and wall oven pages describe as instructions or settings, not errors. Press Start for PUSH, wait for Lo to give way to a temperature, hold Start/Enter for LOC, and press Cancel for a power-loss clock. [1][2][3][5]

A flashing Sanitize light, a Control light that blinks three times, and every cycle and option light flashing are not F-E codes on a Maytag dishwasher. They point to water that was too cool, a locked panel, and a door opened mid-cycle. Check those, close the door, and power-cycle for 30 seconds if the pattern stays. [1][2][3]

On a Maytag dryer, group the codes by the first thing each one wants. F4 E3 and the AF or Check Vent light mean airflow: clean the lint screen and vent. F4 E4 and L2 mean the household supply: check both breakers. F1 E1, F3 E3, F4 E1 and F6 E1 mean a breaker reset. PF means the cycle was cut short by a power failure. [1][3][4][5][6][7][8]

After a power outage, a Maytag French-door refrigerator may show PO, which means the freezer reached 18 degrees F (-8 degrees C) or more. Press Measured Fill under Confirm to acknowledge it, then make sure COOLING OFF is dark, the doors are shut, and note whether the Temperature Alarm is flashing. [1][2][4]

A Maytag front-load washer may use a detergent cartridge or a bulk dispenser. dET means the cartridge was not detected, so reseat it and close the drawer fully. A yellow light means a few cycles are left and red means empty. Detergent Low means the bulk dispenser needs more HE liquid. Clean the drawer parts under running water. [1][2][3][4]

A fan still turning after a Maytag oven is switched off is usually the automatic cooling fan. Maytag says it runs during cooking and after the cycle ends, sometimes for extended periods, to cool the oven cavity and the electronic controls. Open the door: noise that stops is the convection fan, noise that continues is the cooling fan. [1][2]

Maytag's automatic dry cycles read moisture through contact with sensors in the drum, so one towel or a few small items may never register. Use a larger load or a timed cycle such as Quick Dry or Rapid Dry for small loads, keep the dryer level, and treat F3 E5 as a sign five loads passed without sensor data. [1][3]

On a Maytag top-load washer, add clothes loosely and only as high as the highest ring of holes in the basket wall, keep the top of the impeller visible, never wash one absorbent item alone, and arrange bulky items in a ring around the impeller. When oL or OFb shows, cancel or pause, redistribute or remove items and restart. [1][2][3]

Before calling a Maytag French-door ice maker low, run the cube count test: empty the bin, wait 24 hours without using ice, then count. A freezer-only maker should produce 56 to 72 cubes, a refrigerator-section maker 80 to 140, and dual makers 147 to 252. A count in range means the maker is working, and the bin may need 2 to 3 days to fill. [1]

Open the door and check three places: the fold of the rubber seal, the detergent drawer cavity and the bottom of the drum. Each one has its own cause on Maytag's pages.
Read the full sequence
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.

Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.

Water left in the door seal (bellows) of a front-load Maytag washer is usually trapped by dirt, pet hair or a small item under the rubber. Pull the seal back and look all the way around, wipe it clean, and run the Clean Washer cycle each month. A dirty seal can also let water out at the front.

The door seal, or bellows, on a Maytag front-load washer can trap small items, dirt and pet hair, and then hold water. Product Help says to inspect and clean it monthly and to run the Clean Washer cycle monthly. Its small drain holes can clog and slow draining.

F8E2 on a Maytag front-load washer is a dispenser system problem, and Product Help wants you to confirm the drawer or cartridge is not clogged with detergent. On top-load models F8E2 is the bulk dispenser and F3E5 the mini dispenser. dET means the cartridge is not detected.

Many Maytag front-load washers hide a drain pump filter behind the bottom dispenser drawer. Product Help says to clean it occasionally, because a clogged filter makes the washer drain poorly and can lead to F9E1. Catch the water with a flat container and a cloth first.

F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
Maytag deals with repairs its warranty covers. Every repair we complete is backed by our workmanship warranty.
Laundry care, dishwasher and range upkeep, troubleshooting steps and display messages. Each ends with the Maytag Product Help pages behind it.
A message on the screen points to the codes guides. A symptom without any message belongs with troubleshooting. Care guides help you avoid repeats.
No. Guides stick to tasks that are low risk at home, like cleaning a lint screen or a filter. Panels, gas and wiring are for a technician.
Not always. Product Help splits by product type, and the guide says which type it describes. Your owner's manual wins on model details.
Maytag codes, symptoms, parts and service
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.