Maytag washer F8E3 / Water and drain

Maytag washer
error code F8E3

Washer / display reference

For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.

Also printed as F8E3

Last reviewed

Washer / display reference
Meaning
For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Who handles it
Reset, then book
Related codes
Source
F8 E3 - Front Load Washer - Product Help | Maytag

What Maytag washer F8E3 means.

What it means

For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.

What you can safely check

Power and water off before any panel comes off; towels down for spills.

When to call a technician

F8E3 repeats after the reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 6 checks done
  1. Maytag washer F8E3: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Before you start

    Power and water off before any panel comes off; towels down for spills.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Record the code

    Record F8E3 character by character and note the product type: front-load washer.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Cut the power

    Power off for five full minutes, then on, and look for F8E3.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Watch afterward

    Run the washer briefly after the reset and see whether F8E3 comes back.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Appliance-specific check

    Look for water on the floor around the front-load washer before you restart a cycle.

  6. Illustration. Follow your model’s instructions.
    Check 6

    Gather details

    Keep the model number close and note when F8E3 appeared and what the front-load washer was doing.

Does F8E3 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does Maytag print beside F8E3 for a front-load washer?

Here is what Maytag prints for F8E3 on a front-load washer: “The overflow condition occurs if there is too much water or foam in the washer.”

Read the supporting manual

How should I react the moment F8E3 appears?

Leave the washer off power for five full minutes, switch it back on, and check the display for F8E3.

Read the supporting manual

Why do F8E3 and F8E2 sit side by side in Maytag's list?

F8E2 is a separate entry from F8E3 on the front-load washer page, with its own wording.

Read the supporting manual

How careful should I be with the front-load washer while F8E3 is up?

Only restart the front-load washer once the taps are open and the floor is dry. Never open a panel on the front-load washer yourself.

Read the supporting manual

The manual behind the message.

Manufacturer document

F8 E3 - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-11-19; PH 14628 / PH 14628 (front-load washer)

Manufacturer document

F8E3 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13459 / PH 13459 (top-load washer)

F8E3 comes from Maytag Product Help (PH 14628) for the front-load washer, read in November 2026; the F8E3 entry names no models.

Here to help

Good questions.
Clear answers.

Talk to our team
What does Maytag say F8E3 means?

The front-load washer page reads “The overflow condition occurs if there is too much water or foam in the washer.” It prints nothing more about cause.

Will five minutes without power clear F8E3?

Yes, run it as printed and schedule a visit if F8E3 stays.

Does the front-load washer page name a part for F8E3?

No part is named for F8E3; the page gives only the wording above.

What do you need to know about F8E3?

The model and serial numbers, the exact display for F8E3, and what the front-load washer was doing at the time.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.