Start from the symptom
Maytag washer not draining.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Clean the drain pump filter
On a front-load washer with one, the filter can clog with dirt, lint and small items. Product Help says to clean it from time to time.
- 2
Measure the hose in the standpipe
Front-load: no more than 4.5 inches inside the drainpipe. Top-load: no more than 5 inches. Use the U-shaped hose form from the install sheet.
- 3
Leave an air gap
Do not tape the drain hose into the pipe. A loose, secure fit lets air in and stops water from siphoning out during the fill.
- 4
Check standpipe height
For a front-load washer the top of the drain should be at least 30 inches off the floor. Lower, and water can flow out by gravity.
- 5
Look at the hose and the suds
A top-load drain hose must not be kinked or clogged, and cannot rise above 96 inches. Non-HE or excess detergent makes suds that slow the spin and leave loads wet.
Systems a technician may investigate.
These parts tie in to the symptom. Noticing it does not prove that any single one has worn out.

Washer drain hose (F9E1, drn, Ld)
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.

Washer drain pump filter
Many Maytag front-load washers hide a drain pump filter behind the bottom dispenser drawer. Product Help says to clean it occasionally, because a clogged filter makes the washer drain poorly and can lead to F9E1. Catch the water with a flat container and a cloth first.
If the display adds a code.
Water and drain
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Water and drain
The Maytag page for drn on a top-load washer states “If F9 E1 (drain pump system problem-long drain) appears in the display, the washer is taking too long to...” No reset is printed for it, so schedule a visit if it keeps appearing.
Water and drain
On a top-load washer, the entry for Ld says “If Ld(drain pump system problem-long drain) appears in the display, the washer is taking too long to drain...” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Display and signals
Maytag's front-load washer page words SUD like this: “Sud or Sd is displayed:.” No reset is printed for it, so schedule a visit if it keeps appearing.
Read the related care guide.

Water still in the washer after the cycle: where it sits matters.
Where the water sits tells you what to do. A little in the dispenser area is normal, and more than half an inch after a thorough drawer cleaning is a service call. Water under the door seal usually means trapped lint, hair or small items, so clean the bellows monthly. Water in the tub with wet clothes points to an unbalanced load or a low spin, and Drain and Spin fixes that. [1][2][3][4]

A top-loader that will not agitate or spin: start with the load and the lid.
A Maytag top-load washer that stops agitating or spinning is most often reacting to the load or the setup, not to a broken part. Check balance, the cycle choice, the drain hose and standpipe, the level of the cabinet, a recent power cut, and anything resting on or under the lid. If dU or LdL stays on after that, book a technician. [1][2][3][4]
When observation becomes a service request.
Leave internal testing to a technician.
Water is still in the tub after the hose, standpipe and filter checks.
The display shows F9E1, drn or Ld and keeps coming back.
Water backs up out of the standpipe or laundry tub.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag washer not draining advice. Read the manual for your own model.
- Not Draining - Front Load Washer - Product Help | Maytag
- Not Draining - Washer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Why does my Maytag washer finish with water still in the drum?
Start at the drain: hose depth, standpipe height, tape around the hose, and the drain pump filter on front-load models. Product Help lists these as the first checks before any service call.
What hose depth does the standpipe allow?
No more than 4.5 inches on a front-load washer and no more than 5 inches on a top-load washer. The U-shaped hose form that comes with the washer sets the right length.
Can too much detergent keep a Maytag washer from draining?
Yes, on a top-load. Regular detergent, or more than the dose, builds suds, and Product Help says the washer then spins slower and loads come out very wet. Measure HE detergent to the load.
Is a washer that will not drain an emergency?
Not usually, but water sitting in the tub can smell and leak if the hose is loose. Switch the washer off, then book a technician if the drain checks did not clear it.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Maytag washer F9E1 error code
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Maytag washer not draining
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Washer drain hose (F9E1, drn, Ld)
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.
Washer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.