What it means
The Maytag page for drn on a top-load washer states “If F9 E1 (drain pump system problem-long drain) appears in the display, the washer is taking too long to...” No reset is printed for it, so schedule a visit if it keeps appearing.
Maytag washer drn / Water and drain
The Maytag page for drn on a top-load washer states “If F9 E1 (drain pump system problem-long drain) appears in the display, the washer is taking too long to...” No reset is printed for it, so schedule a visit if it keeps appearing.
Also printed as drn
The Maytag page for drn on a top-load washer states “If F9 E1 (drain pump system problem-long drain) appears in the display, the washer is taking too long to...” No reset is printed for it, so schedule a visit if it keeps appearing.
Power and water off before any panel comes off; towels down for spills.
drn returns, or the top-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Match the label on your appliance to the top-load washer list before you rely on the wording for drn.

No reset is printed here; note the behavior of the washer around drn instead.

Keep the model number close and note when drn appeared and what the top-load washer was doing.

Note whether water is left in the drum or tub.
Write down the model and serial numbers and the exact drn wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain.
Read the definitiondrn is covered by this wording on the top-load washer page: “If F9 E1 (drain pump system problem-long drain) appears in the display, the washer is taking too long to drain water.”
Read the supporting manualMaytag's page for drn gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualdU is a separate entry from drn on the top-load washer page, with its own wording.
Read the supporting manualDo not rerun cycles on the top-load washer while water is left inside; it can overflow. If drn keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-07-03; PH 13148 / PH 13148 (top-load washer)
drn comes from Maytag Product Help (PH 13148) for the top-load washer, read in November 2026; the drn entry names no models.
On the top-load washer page the line is “If F9 E1 (drain pump system problem-long drain) appears in the display, the washer is taking too long to drain water.” No further cause is given.
Nothing is printed for it, so record the display and schedule us if drn continues.
Not by itself; the page stops at the line it prints.
Tell us the model, the display wording and when drn first showed up.
Maytag codes, symptoms, parts and service
Maytag's top-load washer page words dU like this: “If dU (Lid cannot unlock) appears in display, the washer detects that there are objects on washer lid...” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.