Inside the appliance
Washer drain hose (F9E1, drn, Ld). In plain English.
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.

Where it fits.
Washer drain hose (F9E1, drn, Ld) in the appliance
Behind the washer, where the hose goes into the standpipe or laundry tub. Pull the washer forward carefully; do not bend the hose.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Washer drain hose (F9E1, drn, Ld) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Measure the insertion
Front-load: no more than 4.5 in (113 mm) into the drainpipe. The top-load page says 5 in (20.3 cm).
- 2
Keep an air gap
Do not seal the hose into the pipe with tape. The gap lets air in and stops siphoning.
- 3
Mind the height
The maximum drain hose height is 96 in from the floor.
- 4
Straighten the hose
Remove kinks and clear any blockage in the drainpipe or laundry tub.
Cleaning or replacement?
Leave internal testing to a technician.
F9E1 returns after the hose and standpipe check.
Water backs up in the standpipe or utility sink.
Clothes come out soaking wet with the hose clear.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Washer drain hose (F9E1, drn, Ld) advice. Read the manual for your own model.
- F9 E1 - Front Load Washer - Product Help | Maytag
- F9E1 - Error Code - Product Help | Maytag
- Not Draining - Washer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
What does F9E1 mean on a Maytag washer?
The washer is taking too long to drain. Product Help lists the drain hose, the drain pump filter and the door seal as things to check.
Why must the hose not be taped?
Product Help says there must be a gap between hose and pipe to break suction, so water is not pulled from the washer as it fills.
Why do the pages give 4.5 and 5 inches?
The front-load page says 4.5 inches and the top-load page says 5 inches. Use the figure for your washer type and the installation sheet.
Is HE detergent part of this?
On the top-load page, yes: non-HE detergent or too much can make suds and a slow spin, leaving loads wet.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Maytag washer F9E1 error code
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Maytag washer not draining
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Washer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.


