What it means
On a top-load washer, the entry for Ld says “If Ld(drain pump system problem-long drain) appears in the display, the washer is taking too long to drain...” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer Ld / Water and drain
On a top-load washer, the entry for Ld says “If Ld(drain pump system problem-long drain) appears in the display, the washer is taking too long to drain...” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as Ld
On a top-load washer, the entry for Ld says “If Ld(drain pump system problem-long drain) appears in the display, the washer is taking too long to drain...” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
Ld repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Match the label on your appliance to the top-load washer list before you rely on the wording for Ld.

Maytag prints no reset for Ld, so record what the washer does rather than guessing a fix.

Note the model and the moment Ld showed up; both help us plan.

Note whether water is left in the drum or tub.
Note the model and the moment Ld showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain.
Read the definitionHere is what Maytag prints for Ld on a top-load washer: “If Ld(drain pump system problem-long drain) appears in the display, the washer is taking too long to drain water.”
Read the supporting manualMaytag's page for Ld gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualLdU is a separate entry from the code on the top-load washer page, with its own wording.
Read the supporting manualDo not rerun cycles on the top-load washer while water is left inside; it can overflow.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-07-03; PH 13154 / PH 13154 (top-load washer)
Ld comes from Maytag Product Help (PH 13154) for the top-load washer, read in November 2026; the Ld entry names no models.
While Ld shows on a top-load washer, the help page states “If Ld(drain pump system problem-long drain) appears in the display, the washer is taking too long to drain water.” Nothing else is added.
The page prints none. Write down what you see and schedule a visit if Ld keeps appearing.
Not by itself; the page stops at the line it prints.
The model and serial numbers, the exact display for Ld, and what the top-load washer was doing at the time.
Maytag codes, symptoms, parts and service
Maytag's top-load washer page words LdU like this: “If LdU (Lid cannot unlock) appears in the display, the washer detects that objects on the washer lid are...” Nothing else is printed, so schedule a visit if it repeats.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.