Before work starts
Your technician checks the washer, dryer or other appliance, then gives you the cost. The repair goes ahead only with your okay.
Independent appliance repair
We repair Maytag washers, both top and front loading: a washer that will not drain, a door that stays locked, a code on the display, a leak or a thump during spin. Book a technician and we diagnose it on site, with the price agreed before any work starts.


A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.

Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.

Water left in the door seal (bellows) of a front-load Maytag washer is usually trapped by dirt, pet hair or a small item under the rubber. Pull the seal back and look all the way around, wipe it clean, and run the Clean Washer cycle each month. A dirty seal can also let water out at the front.

Shaking, walking and thumping in a Maytag washer usually come from how it sits or how it is loaded: shipping bolts left in, a feet-off-the-floor wobble, a floor that flexes, a bulky single item, or hoses knocking the cabinet. Work through those before you book a technician. Some clunks are normal.
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
For a Maytag top-load washer, Maytag's page for OFb says the washer could not even out an off-balance load by itself and needs you to spread the load around the washplate. Arrange a technician visit with us if it will not go away.
For a Maytag front-load washer, Maytag's page for Int says the cycle was paused or canceled. To reset it, keep the power to the unit cut for 5 minutes before restoring it. Arrange a technician visit with us if the display shows it again after the reset.
LoC on a Maytag front-load washer: Maytag's page says it reminds you that Control Lock is on and has to be released before the controls respond. Nothing here is a repair order; schedule a visit only if it will not clear.
On a front-load washer, dET means the detergent dispenser cartridge is not detected. If you use single-load doses of detergent, you can ignore the message. Otherwise seat the cartridge fully and close the drawer completely.
We pick the part after we read the model label and test the unit. Nothing is ordered ahead of time, and the quote is yours to approve before any work begins.

On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue. Product Help says to shut the door completely, clear anything from the latch, and wipe soap buildup off the lock. F5E1 names the door switch.

F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.

Many Maytag front-load washers hide a drain pump filter behind the bottom dispenser drawer. Product Help says to clean it occasionally, because a clogged filter makes the washer drain poorly and can lead to F9E1. Catch the water with a flat container and a cloth first.

The door seal, or bellows, on a Maytag front-load washer can trap small items, dirt and pet hair, and then hold water. Product Help says to inspect and clean it monthly and to run the Clean Washer cycle monthly. Its small drain holes can clog and slow draining.

F8E2 on a Maytag front-load washer is a dispenser system problem, and Product Help wants you to confirm the drawer or cartridge is not clogged with detergent. On top-load models F8E2 is the bulk dispenser and F3E5 the mini dispenser. dET means the cartridge is not detected.

The balance ring on a Maytag top-load washer is a fluid-filled ring at the top of the tub. As a load shifts, the fluid moves to the opposite side to steady the basket and allow faster spins. Product Help says it is the usual cause of water heard but not seen, and it may slosh when you move the washer.
Three steps from request to repair.
You stay in the loop the whole way.

Pick washer or dryer and tell us what it does: no spin, no heat, loud thumping. Book online any time.

The technician tests the machine and quotes the work. You approve the price before a tool comes out.

After the repair the technician runs the machine with you and explains what was changed.
Product Help has a page for each F and E pair, plus OFb, Int, LoC and dET. Note the exact string.
The washer pages say to unplug it for five minutes, then plug it back in.
Front-load: no more than 4.5 in into the drainpipe, not taped, no kinks. The top-load page says 5 in.
Clear the latch of clothing, wipe soap off the lock, and know that some cycles hold the door until you press Cancel.
OFb means cancel, run a drain-only cycle if water remains, then rearrange or remove items.
F9E1 returns after the hose and the drain pump filter are clear.
After a two-minute unplug and a Drain and Spin run, the door stays locked.
Water pools under the washer.
Thumping or banging continues once the load is balanced.
Arrange a diagnosticYour technician checks the washer, dryer or other appliance, then gives you the cost. The repair goes ahead only with your okay.
Maytag deals with repairs its warranty covers. Every repair we complete is backed by our workmanship warranty.
Yes. Product Help keeps separate pages for each type, and so do we when the steps differ, like the drain hose depth.
It is draining too slowly. Check the hose depth, kinks, the drain pump filter on front-loads, and the door seal. If it keeps returning, schedule us.
A Fresh Hold cycle keeps it locked until you press Cancel. Otherwise unplug for two minutes and run Drain and Spin.
We give you the diagnosis and the price first. You decide before any work starts.
For a unit still covered by the manufacturer's warranty, the maker takes that repair. After coverage ends, schedule a technician with us and approve the quote first.
Maytag codes, symptoms, parts and service
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue. Product Help says to shut the door completely, clear anything from the latch, and wipe soap buildup off the lock. F5E1 names the door switch.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.