What it means
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Maytag washer F9E1 / Water and drain
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Also printed as F9E1
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Check the exact spelling of F9E1 on the display (capitals, spaces, dashes) along with the product type: front-load washer and top-load washer.
F9E1 keeps showing after you have run the checks above.
Your Maytag to-do list, saved here on this device

Check the exact spelling of F9E1 on the display (capitals, spaces, dashes) along with the product type: front-load washer and top-load washer.

Note when it appears and whether anything changes after you cancel the cycle or set the product down for a few minutes.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain.
Read the definition
Component reference
Many Maytag front-load washers hide a drain pump filter behind the bottom dispenser drawer.
Read the definition
Component reference
The door seal, or bellows, on a Maytag front-load washer can trap small items, dirt and pet hair, and then hold water.
Read the definitionThe front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain.
Read the supporting manualNo reset interval is printed for it.
Read the supporting manualF9E1 is not one fixed meaning: Maytag's pages differ by product type (front-load washer and top-load washer), so match it to yours.
Read the supporting manualSchedule one with us if F9E1 keeps showing after you have run the checks above. Have the exact display wording and the model number ready.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14629 / PH 14629 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 13461 / PH 13461 (top-load washer)
Scope: Maytag front-load washer and top-load washer. Source pages: Maytag Product Help, PH 14629, 13461, checked November 2026.
The front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain.
No reset interval is printed on the page. Note when the message appears, and schedule a visit if it will not clear.
No part is named on the page. It describes the condition and what you can do about it.
Schedule one if F9E1 keeps showing after you have run the checks above. Until then, the steps above are all the page asks of you.
No. Maytag's pages differ by product type (front-load washer and top-load washer), so match it to yours.
Maytag codes, symptoms, parts and service
For a Maytag front-load washer, Maytag's page for Int says the cycle was paused or canceled. To reset it, keep the power to the unit cut for 5 minutes before restoring it. Arrange a technician visit with us if the display shows it again after the reset.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.