Read the whole display
Say whether the washer is top-load or front-load, and give the exact code, including small letters.
Model-specific code library
We decode 94 washer codes and messages: F#E# codes, short words such as LoC, dET and OFb, and reminder messages, tied to the top-load or front-load tree that prints them.
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Read the F9E1 checks96 researched washer codes. A message can mean something different on each Maytag model, so trust the manual that came with yours.
On a front-load washer, dET means the detergent dispenser cartridge is not detected. If you use single-load doses of detergent, you can ignore the message. Otherwise seat the cartridge fully and close the drawer completely.
Owner checks firstDetergent Level Indicator on a Maytag front-load washer is explained as “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” Nothing else is printed, so schedule a visit if it repeats.
Information onlyMaytag’s top-load washer page for F0E0 (PH 13423) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F0E0 returns.
Reset, then bookMaytag’s front-load and top-load washer pages for F1E1 (PH 14596 and PH 13431) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F1E1 returns.
Reset, then bookOn a front-load washer, the entry for 1h, 2h, 3h....up to 12h says “When the display shows a number up to 12, followed by an 'h,' the Delay Wash has been activated.” No reset is printed for it, so schedule a visit if it keeps appearing.
Information onlyThe top-load page defines F0E3 as an overload: the load is too heavy and the overload recovery cycle is running. The front-load page prints only a reset. Reload loosely and balanced; if it persists, call for service.
Technician visitFor a top-load washer showing Add Garment Light On, Maytag prints “When Add Garment is lit, you may pause the cycle, open the lid, and add items.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Information onlyFor a top-load washer showing Cycle Complete Light On, Maytag prints “It will remain on until the lid is opened or cancel is pressed.” Nothing else is printed, so schedule a visit if it repeats.
Information onlyOn a front-load washer, the entry for Beeping and Audio Tones says “These sounds are cycle signal tones that are part of normal operation.” Nothing else is printed, so schedule a visit if it repeats.
Information onlyOn a front-load washer, the entry for CL Code says “The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Information onlyOn a top-load washer, F2E2 is headed “Keypad.” The front-load page prints only a title and a reset. Cut power for 5 minutes and restart; if F2E2 returns, schedule a technician.
Reset, then bookFor a top-load washer showing F2E3, Maytag prints “The F2 E3 alert indicates there may be an issue with the appliance control unit, user interface or associated...” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
Reset, then bookF7E1 on a Maytag front-load washer is explained as “This code indicates a motor speed sensing error, the motor can not achieve the correct speed for the cycle...” Try the five-minute power-off reset, and schedule a visit if the code returns.
Reset, then bookMaytag's top-load washer page words F7E4 like this: “F7E4 - Shifter.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Reset, then bookOn Maytag's commercial-grade residential washer, F8 E1 means the washer is taking too long to fill, or it is filling and draining at the same time. Check the drain hose, confirm both hot and cold supplies are on, latch the lid and press Start for up to 3 seconds.
Owner checks firstOn Maytag's commercial-grade residential washer, LF (too long to fill) means the washer is taking too long to fill, or is filling and draining. Check the drain hose depth, make sure hot and cold water are both on, latch the lid and press Start for up to 3 seconds.
Owner checks firstMost washer F-codes print a reset and no cause. F-F or E, an old web name, is printed nowhere. The same code string can read differently on top-load and front-load pages.

We decode 94 washer codes and messages: F#E# codes, short words such as LoC, dET and OFb, and reminder messages, tied to the top-load or front-load tree that prints them.
Most washer F-codes print a reset and no cause. F-F or E, an old web name, is printed nowhere. The same code string can read differently on top-load and front-load pages.
Say whether the washer is top-load or front-load, and give the exact code, including small letters.
Unplug the washer before looking behind a panel, and mop up any water on the floor first.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.
Water left in the door seal (bellows) of a front-load Maytag washer is usually trapped by dirt, pet hair or a small item under the rubber. Pull the seal back and look all the way around, wipe it clean, and run the Clean Washer cycle each month. A dirty seal can also let water out at the front.
Follow the guide for your own model, and see how we research these pages.
Most washer F-codes print a reset and no cause. F-F or E, an old web name, is printed nowhere. The same code string can read differently on top-load and front-load pages.
Take a picture of the full washer display and the model label. Say what the machine was in the middle of when the message came up, and do not lean on an explanation written for a different appliance.
An old search phrase is not proof from the manufacturer. If our washer documents say nothing about a message, we still list it by name and send you toward help, without blaming any part.
Open any manufacturer document in this washer library and check the model on its cover against the label on your machine. Another model has its own owner’s guide.