What it means
On a top-load washer, F2E2 is headed “Keypad.” The front-load page prints only a title and a reset. Cut power for 5 minutes and restart; if F2E2 returns, schedule a technician.
Maytag washer F2E2 / User interface
On a top-load washer, F2E2 is headed “Keypad.” The front-load page prints only a title and a reset. Cut power for 5 minutes and restart; if F2E2 returns, schedule a technician.
Also printed as F2E2
On a top-load washer, F2E2 is headed “Keypad.” The front-load page prints only a title and a reset. Cut power for 5 minutes and restart; if F2E2 returns, schedule a technician.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
F2E2 returns after the 5-minute reset.
Your Maytag to-do list, saved here on this device

The top-load heading is Keypad, so look for a pressed or damp button before you reset.

Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

Select a short cycle and see whether the keypad responds.

Does F2E2 appear at power-up or after pressing a key? That helps us.

The word Keypad appears only on the top-load page.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The top-load page is headed “F2E2 - Keypad” and gives the 5-minute power reset. The front-load page is headed “F2E2 Error Code” with the same reset and no cause.
Read the supporting manualIt is the only cause in the text. A keypad code points at the control panel, not at water or drain parts.
Read the supporting manualF2E1 is printed with the same reset on both trees and no cause. F2E2 on the top-load tree is the one that names the keypad.
Read the supporting manualThe top-load F6E2 page calls it a washer reboot alert and blames the appliance control unit, user interface or wiring.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14602 / PH 14602 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13434 / PH 13434 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13433 / PH 13433 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 13447 / PH 13447 (top-load washer)
The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14602 (front-load), PH 13434 (top-load), with the F2E1 and F6E2 top-load pages.
On a top-load washer the page heading says Keypad, so the keypad is the label Maytag prints. The front-load page for the same code gives no label at all.
Maytag prints no cleaning step for F2E2. The only step is the power reset, though checking that no button is held down or damp is a harmless first look.
Five minutes. Unplug the washer, or switch off its breaker, for 5 minutes and then restore power. If F2E2 returns, schedule a visit.
It has the same 5-minute reset but no Keypad label. The two trees therefore agree on the fix and differ only in how much cause they print.
Maytag codes, symptoms, parts and service
Maytag’s front-load and top-load washer pages for F2E1 (PH 14601 and PH 13433) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F2E1 returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.