What it means
Maytag’s front-load and top-load washer pages for F1E2 (PH 14597 and PH 13432) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F1E2 returns.
Maytag washer F1E2 / Reset only
Maytag’s front-load and top-load washer pages for F1E2 (PH 14597 and PH 13432) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F1E2 returns.
Also printed as F1E2
Maytag’s front-load and top-load washer pages for F1E2 (PH 14597 and PH 13432) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F1E2 returns.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
F1E2 repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Match the label on your appliance to the front-load washer list before you rely on the wording for F1E2.

Power off for five full minutes, then on, and look for F1E2.

Give the washer a minute on screen after the reset; a returning F1E2 means schedule a visit.

The control board lives behind panels on the front-load washer; keep them closed.
Keep the model number close and note when F1E2 appeared and what the front-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Nothing. The front-load and top-load washer pages (PH 14597 and PH 13432, modified November 2025 and May 2025) gives no cause, no part and no meaning for F1E2; it has only a power reset.
Read the supporting manualUnplug the washer for 5 minutes and plug it back in, or switch its breaker off for 5 minutes and back on. Maytag compares it to restarting a computer.
Read the supporting manualMaytag says resetting the control can sometimes solve the issues you are experiencing, but it does not promise it. After the 5 minutes, watch the display for F1E2; if it is gone, run a short cycle and keep an eye on the washer.
Read the supporting manualGive us the model and serial numbers, the exact display, and what the washer was doing when F1E2 appeared. Say whether the reset cleared it, even for a short time, because a code that returns is the reason to book a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14597 / PH 14597 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13432 / PH 13432 (top-load washer)
Facts for F1E2 come from Maytag Product Help, front-load and top-load washer pages (PH 14597 and PH 13432), read in November 2026. The pages list no models.
No. The front-load and top-load washer pages prints only the reset instruction and no cause, so we cannot name a failed part and will not guess one.
Five minutes, as printed. Unplug the washer or switch off its breaker for the full 5 minutes before restoring power, because a shorter wait may not reset the control.
No. Both pages print the same reset and no cause, so you can follow the same steps on either type of washer.
Book a visit if F1E2 returns after the 5-minute reset, or if the washer behaves oddly in other ways. Have the model and serial numbers ready.
Maytag codes, symptoms, parts and service
Maytag’s front-load and top-load washer pages for F1E1 (PH 14596 and PH 13431) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F1E1 returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.