Inside the appliance
Washer water level sensing. In plain English.
Water level sensing is how a Maytag washer knows how much water is in the tub. Product Help words F3 E1 as the washer being unable to detect the water level, and points to the control unit or its wiring. F8 E1 and the Wash light name the same job: the control is not seeing the water change as expected.

Where it fits.
Washer water level sensing in the appliance
Inside the washer. Product Help does not name where level sensing is done.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Washer water level sensing trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag washer not draining
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.

Maytag washer leaking water
Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Cycle the power
Unplug the washer for 5 minutes, then plug it back in. Product Help says this resets the control.
- 2
Open both faucets
Hot and cold supply must both be fully open. Check that the inlet hoses have no kinks.
- 3
Check the drain hose
The Wash light page says a hose too far down the drainpipe or laundry tub can be the reason. Do not tape it into the drainpipe.
- 4
Check the Water Level knob
On models with the option, Auto Sensing sets the level by load; Deep Water Wash adds the maximum water and a longer fill.
- 5
Allow for the Bulky cycle
Bulky fills in stages while the washer senses the load. Product Help says this can take 10 to 12 minutes.
Cleaning or replacement?
Leave internal testing to a technician.
F3 E1, F8 E1 or the Wash light returns after the reset and the water checks.
The washer fills, then stops with the lid locked.
Water level seems wrong with open faucets and clear hoses.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Washer water level sensing advice. Read the manual for your own model.
- F3E1 - Error Code - Product Help | Maytag
- Wash Light On or Flashing - Product Help | Maytag
- Not Filling or Long Fill - Washer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
What does F3 E1 mean on a Maytag washer?
On the top-load page it means the washer cannot detect the water level. Maytag names the control unit or associated wiring. The printed step is a 5-minute reset.
What is Auto Sensing?
On models with a Water Level knob, Auto Sensing lets the washer sense load size and fill to match. Deep Water Wash adds the maximum water instead.
Why is the Wash light flashing?
Product Help says the water level has not changed for a while, or water is present but the control does not see it change. Check faucets, inlet screens and the drain hose.
Why does the Bulky cycle fill so slowly?
It fills in stages while agitating and sensing. Product Help says it can take 10 to 12 minutes, so a slow fill is not always a problem.
Can I fix the sensing myself?
Only the checks above. Product Help names the control unit and wiring, which are not owner repairs. Book a visit if the reset does not clear it.
Maytag codes, symptoms, parts and service
From the message to what you do next.
F3E1
On a top-load washer, F3E1 means the washer cannot detect the water level, and Maytag points to the appliance control unit or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Maytag washer not draining
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Washer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.
