What it means
On a front-load washer, the entry for F8E1 says “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer F8E1 / Water and drain
On a front-load washer, the entry for F8E1 says “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as F8E1
On a front-load washer, the entry for F8E1 says “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Power and water off before any panel comes off; towels down for spills.
F8E1 repeats after the reset.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Record F8E1 character by character and note the product type: front-load washer.

Maytag prints no reset for F8E1, so record what the washer does rather than guessing a fix.

Write down the model and serial numbers and the exact F8E1 wording before you call.

Check both water taps behind the front-load washer are fully open and the hoses are not kinked.
Keep the model number close and note when F8E1 appeared and what the front-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Here is what Maytag prints for F8E1 on a front-load washer: “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.”
Read the supporting manualNo reset is printed for F8E1 on the front-load washer page. Writing down what the washer does around the code is the useful thing to do.
Read the supporting manualThe front-load washer list prints F7E9 next to F8E1, but with a different line. Look up the one on your display.
Read the supporting manualIf water collects on the floor, shut the taps and switch the front-load washer off. If F8E1 keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14626 / PH 14626 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 13457 / PH 13457 (top-load washer)
Facts for F8E1 are from the front-load washer table (PH 14626) of Maytag Product Help, checked November 2026; no model list is printed.
On the front-load washer page the line is “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” No further cause is given.
No; Maytag gives F8E1 no reset steps. If it repeats, schedule a visit.
Not by itself; the page stops at the line it prints.
Model and serial numbers plus a note of what happened when F8E1 appeared.
Maytag codes, symptoms, parts and service
On a top-load washer, F7E9 indicates there may be an issue with the main router, user interface or associated wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.