What it means
On a top-load washer, F7E7 indicates an issue with the appliance control unit, user interface or associated wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Maytag washer F7E7 / User interface
On a top-load washer, F7E7 indicates an issue with the appliance control unit, user interface or associated wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Also printed as F7E7
On a top-load washer, F7E7 indicates an issue with the appliance control unit, user interface or associated wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Power and water off before any panel comes off; towels down for spills.
F7E7 returns after the 5-minute reset.
Your Maytag to-do list, saved here on this device

Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

See whether the display and keys behave normally after power returns.

Note if F7E7 comes back.

F7E9 blames the main router, user interface or wiring.

The control-unit wording is on the top-load page only.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The page asks “Did you receive an F7E7?” and says the alert indicates an issue with the appliance control unit, user interface or associated wiring.
Read the supporting manual“F7E7 Error Code” and the 5-minute reset, with no cause.
Read the supporting manualF7E9 says there may be an issue with the main router, user interface or wiring. The word router is printed as written.
Read the supporting manualF6E2 uses the same sentence as F7E7, with the label washer reboot alert.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 14621 / PH 14621 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13455 / PH 13455 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13456 / PH 13456 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 13447 / PH 13447 (top-load washer)
The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14621 (front-load), PH 13455 (top-load), with the top-load F7E9 and F6E2 pages.
It is the control panel with its keys and display. The page lists it together with the appliance control unit and the wiring as the possible issue.
The cause list matches. Both top-load pages name the appliance control unit, user interface or wiring, but F6E2 carries the label washer reboot alert and F7E7 does not.
Five minutes. Unplug the washer, or switch off its breaker, for 5 minutes, then restore power.
After a clean reset, yes. If F7E7 returns, stop relying on the washer and book a visit.
Maytag codes, symptoms, parts and service
Maytag’s front-load and top-load washer pages for F7E6 (PH 14620 and PH 13454) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F7E6 returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.