Maytag washer F7E6 / Reset only

Maytag washer
error code F7E6

Washer / display reference

Maytag’s front-load and top-load washer pages for F7E6 (PH 14620 and PH 13454) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F7E6 returns.

Also printed as F7E6

Last reviewed

Washer / display reference
Meaning
Maytag’s front-load and top-load washer pages for F7E6 (PH 14620 and PH 13454) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F7E6 returns.
Who handles it
Reset, then book
Related codes
Source
F7 E6 - Front Load Washer - Product Help | Maytag

What Maytag washer F7E6 means.

What it means

Maytag’s front-load and top-load washer pages for F7E6 (PH 14620 and PH 13454) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F7E6 returns.

What you can safely check

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

When to call a technician

F7E6 repeats after the reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 6 checks done
  1. Maytag washer F7E6: Hand pressing a round button on a top-load washer panel next to a dial and a lit display, with a detergent jug on the shelf above
    Illustration. Follow your model’s instructions.
    Before you begin

    Before you start

    Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Match your model

    Match the label on your appliance to the front-load washer list before you rely on the wording for F7E6.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Reset the power

    Wait five minutes without power before you check for F7E6 again.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Check the display

    Once power is back, keep an eye on the washer for about a minute for F7E6.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Appliance-specific check

    The control board lives behind panels on the front-load washer; keep them closed.

  6. Illustration. Follow your model’s instructions.
    Check 6

    Write it down

    Keep the model number close and note when F7E6 appeared and what the front-load washer was doing.

Does F7E6 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 2Control board
  3. 4Motor wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does Maytag say F7E6 means?

Nothing. The front-load and top-load washer pages (PH 14620 and PH 13454, modified May 2025) gives no cause, no part and no meaning for F7E6; it has only a power reset.

Read the supporting manual

How do I reset the washer for F7E6?

Unplug the washer for 5 minutes and plug it back in, or switch its breaker off for 5 minutes and back on. Maytag compares it to restarting a computer.

Read the supporting manual

Will the reset fix F7E6?

Maytag says resetting the control can sometimes solve the issues you are experiencing, but it does not promise it. After the 5 minutes, watch the display for F7E6; if it is gone, run a short cycle and keep an eye on the washer.

Read the supporting manual

What should I tell the technician about F7E6?

Give us the model and serial numbers, the exact display, and what the washer was doing when F7E6 appeared. Say whether the reset cleared it, even for a short time, because a code that returns is the reason to book a visit.

Read the supporting manual

The manual behind the message.

Manufacturer document

F7 E6 - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 14620 / PH 14620 (front-load washer)

Manufacturer document

F7E6 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13454 / PH 13454 (top-load washer)

Facts for F7E6 come from Maytag Product Help, front-load and top-load washer pages (PH 14620 and PH 13454), read in November 2026. The pages list no models.

Here to help

Good questions.
Clear answers.

Talk to our team
Does Maytag say what F7E6 means on a washer?

No. The front-load and top-load washer pages prints only the reset instruction and no cause, so we cannot name a failed part and will not guess one.

How long should the washer stay without power for F7E6?

Five minutes, as printed. Unplug the washer or switch off its breaker for the full 5 minutes before restoring power, because a shorter wait may not reset the control.

Do the front-load and top-load pages differ for F7E6?

No. Both pages print the same reset and no cause, so you can follow the same steps on either type of washer.

When should I book a visit for F7E6?

Book a visit if F7E6 returns after the 5-minute reset, or if the washer behaves oddly in other ways. Have the model and serial numbers ready.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.