What it means
Maytag’s front-load and top-load washer pages for F7E2 (PH 14618 and PH 13451) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F7E2 returns.
Maytag washer F7E2 / User interface
Maytag’s front-load and top-load washer pages for F7E2 (PH 14618 and PH 13451) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F7E2 returns.
Also printed as F7E2
Maytag’s front-load and top-load washer pages for F7E2 (PH 14618 and PH 13451) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F7E2 returns.
Power and water off before any panel comes off; towels down for spills.
F7E2 repeats after the reset.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Check that your appliance is a front-load washer and copy F7E2 exactly as the display shows it.

Wait five minutes without power before you check for F7E2 again.

Give the washer a minute on screen after the reset; a returning F7E2 means schedule a visit.

The control board lives behind panels on the front-load washer; keep them closed.
Keep the model number close and note when F7E2 appeared and what the front-load washer was doing.
The dishwasher page names a wash motor. The washer pages print no cause, so only the reset applies to the washer.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Nothing. The front-load and top-load washer pages (PH 14618 and PH 13451, modified November 2025 and May 2025) gives no cause, no part and no meaning for F7E2; it has only a power reset.
Read the supporting manualUnplug the washer for 5 minutes and plug it back in, or switch its breaker off for 5 minutes and back on. Maytag compares it to restarting a computer.
Read the supporting manualMaytag says resetting the control can sometimes solve the issues you are experiencing, but it does not promise it. After the 5 minutes, watch the display for F7E2; if it is gone, run a short cycle and keep an eye on the washer.
Read the supporting manualGive us the model and serial numbers, the exact display, and what the washer was doing when F7E2 appeared. Say whether the reset cleared it, even for a short time, because a code that returns is the reason to book a visit.
Read the supporting manualYes, the dishwasher page lists “Potential Cause: Wash Motor Error,” with a power cycle and service if it returns.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14618 / PH 14618 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13451 / PH 13451 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12630 / PH 12630 (dishwasher)
Facts for F7E2 come from Maytag Product Help, front-load and top-load washer pages (PH 14618 and PH 13451), read in November 2026. The pages list no models.
No. The front-load and top-load washer pages prints only the reset instruction and no cause, so we cannot name a failed part and will not guess one.
Five minutes, as printed. Unplug the washer or switch off its breaker for the full 5 minutes before restoring power, because a shorter wait may not reset the control.
No. Both pages print the same reset and no cause, so you can follow the same steps on either type of washer.
Book a visit if F7E2 returns after the 5-minute reset, or if the washer behaves oddly in other ways. Have the model and serial numbers ready.
Maytag does not say so for the washer. The dishwasher page names a wash motor error, but the washer pages print only a power reset and no cause.
Maytag codes, symptoms, parts and service
F7E1 on a Maytag front-load washer is explained as “This code indicates a motor speed sensing error, the motor can not achieve the correct speed for the cycle...” Try the five-minute power-off reset, and schedule a visit if the code returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.