What it means
On a top-load washer, F6E3 is a “washer reboot alert” with the same cause as F6E2: the appliance control unit, user interface or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Maytag washer F6E3 / User interface
On a top-load washer, F6E3 is a “washer reboot alert” with the same cause as F6E2: the appliance control unit, user interface or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Also printed as F6E3
On a top-load washer, F6E3 is a “washer reboot alert” with the same cause as F6E2: the appliance control unit, user interface or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Power and water off before any panel comes off; towels down for spills.
F6E3 returns after the 5-minute reset.
Your Maytag to-do list, saved here on this device

Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

Note if it flickers.

Start a short cycle.

The wording is the same; write down which you saw.

The cause is printed only on top-load.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The page asks “Did you receive an F6 E3 washer reboot alert?” and says it indicates an issue with the appliance control unit, user interface or associated wiring.
Read the supporting manual“F6E3 Error Code” and the reset only.
Read the supporting manualNot in the text.
Read the supporting manualF7E9 says there may be an issue with the main router, user interface or wiring.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14616 / PH 14616 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13448 / PH 13448 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 13447 / PH 13447 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13456 / PH 13456 (top-load washer)
The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14616 (front-load), PH 13448 (top-load), with the top-load F6E2 and F7E9 pages.
The text matches on both trees: the top-load pages share the washer reboot alert sentence and cause list, and the front-load pages share the bare reset. Only the code on your display separates them.
No. The page does not tell you to replace anything. It lists the appliance control unit, user interface or wiring as possible issues, and a technician has to test them.
Five minutes. Unplug the washer, or switch off its breaker, for 5 minutes, then restore power.
Treat it as a repeating alert. Write down the dates it appeared and book a visit rather than resetting again and again.
Maytag codes, symptoms, parts and service
On a top-load washer, F6E2 is a “washer reboot alert” that indicates an issue with the appliance control unit, user interface or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.