What it means
On a top-load washer, F6E2 is a “washer reboot alert” that indicates an issue with the appliance control unit, user interface or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Maytag washer F6E2 / User interface
On a top-load washer, F6E2 is a “washer reboot alert” that indicates an issue with the appliance control unit, user interface or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Also printed as F6E2
On a top-load washer, F6E2 is a “washer reboot alert” that indicates an issue with the appliance control unit, user interface or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Power and water off before any panel comes off; towels down for spills.
F6E2 returns after the 5-minute reset.
Your Maytag to-do list, saved here on this device

Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

A reboot alert may repeat; see whether the display comes back normal.

Note any dark display, stuck key or flicker.

Start a short cycle and see whether F6E2 returns.

The control-unit explanation is on the top-load page only.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The page asks “Did you receive a F6 E2 washer reboot alert?” and says the alert indicates an issue with the appliance control unit, user interface or associated wiring.
Read the supporting manual“F6 E2 Error Code” and the reset only.
Read the supporting manualThe top-load F6E3 page uses the same sentence. The F7E7 page also uses it.
Read the supporting manualMaytag uses the phrase without defining it.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14615 / PH 14615 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 13447 / PH 13447 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13448 / PH 13448 (top-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13455 / PH 13455 (top-load washer)
The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14615 (front-load), PH 13447 (top-load), with the top-load F6E3 and F7E7 pages.
The pages give no severity. The top-load page calls it a washer reboot alert and lists the control unit, user interface or wiring, so treat a repeating code as a reason to book a visit.
It is one of three possibilities on the top-load page: the appliance control unit, the user interface or the associated wiring. The page does not say which.
Five minutes. Unplug the washer, or switch off its breaker, for 5 minutes, then restore power and run a short cycle.
Note the washer model, whether it is top-load or front-load, and any display oddities such as flicker or dead keys. Also say whether the reset cleared the code.
Maytag codes, symptoms, parts and service
Maytag’s front-load and top-load washer pages for F6E1 (PH 14614 and PH 13446) print no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F6E1 returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.