What it means
For a top-load washer showing LF, Maytag prints “If F8 E1 or LF (long fill) appears in the display, the washer is taking too long to fill.” No reset is printed for it, so schedule a visit if it keeps appearing.
Maytag washer LF / Water and drain
For a top-load washer showing LF, Maytag prints “If F8 E1 or LF (long fill) appears in the display, the washer is taking too long to fill.” No reset is printed for it, so schedule a visit if it keeps appearing.
Also printed as LF
For a top-load washer showing LF, Maytag prints “If F8 E1 or LF (long fill) appears in the display, the washer is taking too long to fill.” No reset is printed for it, so schedule a visit if it keeps appearing.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
LF will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Match the label on your appliance to the top-load washer list before you rely on the wording for LF.

Maytag prints no reset for LF, so record what the washer does rather than guessing a fix.

Write down the model and serial numbers and the exact LF wording before you call.

Look at the inlet hoses: hot and cold must be on the right connections.
Keep the model number close and note when LF appeared and what the top-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
LF is covered by this wording on the top-load washer page: “If F8 E1 or LF (long fill) appears in the display, the washer is taking too long to fill.”
Read the supporting manualMaytag's page for LF gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualHC is a neighbor of LF, not a synonym. The reset may overlap; the text does not.
Read the supporting manualOnly restart the top-load washer once the taps are open and the floor is dry.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 13155 / PH 13155 (top-load washer)
Scope for LF: Maytag top-load washer, PH 13155, checked November 2026. Maytag lists no models on the LF page.
If LF is up on the top-load washer, Maytag's wording is “If F8 E1 or LF (long fill) appears in the display, the washer is taking too long to fill.” That is the whole entry.
There is no reset on that page. Note what happens and book us if LF persists.
Maytag names no part here. Read the message and follow the steps.
Model and serial numbers plus a note of what happened when LF appeared.
Maytag codes, symptoms, parts and service
On a top-load washer, the entry for HC says “If HC (hot and cold hoses reversed) appears in display, it means the hot and cold inlet hoses have been installed incorrectly.” No reset is printed for it, so schedule a visit if it keeps appearing.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.