Maytag washer F3E1 / Water and drain

Maytag washer
error code F3E1

Washer / display reference

On a top-load washer, F3E1 means the washer cannot detect the water level, and Maytag points to the appliance control unit or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.

Also printed as F3E1

Last reviewed

Washer / display reference
Meaning
On a top-load washer, F3E1 means the washer cannot detect the water level, and Maytag points to the appliance control unit or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.
Who handles it
Reset, then book
Related codes
Source
F3 E1 - Front Load Washer - Product Help | Maytag

What Maytag washer F3E1 means.

What it means

On a top-load washer, F3E1 means the washer cannot detect the water level, and Maytag points to the appliance control unit or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.

What you can safely check

Power and water off before any panel comes off; towels down for spills.

When to call a technician

F3E1 returns after the 5-minute reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag washer F3E1: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Reset for 5 minutes

    Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Watch the first fill

    The code is about water level, so see whether the washer fills at all.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Check the faucets

    Make sure both water valves are open. This is our look; the F3E1 page does not print it.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Do not open the control

    The page names the control unit and wiring.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Know your tree

    Water level wording is on the top-load page only.

Does F3E1 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Parts behind the message.

Top-load washer with the lid raised, seen from above, with water partly filling the tub around the center agitator

Component reference

Washer water level sensing

Water level sensing is how a Maytag washer knows how much water is in the tub.

Read the definition

A little more context.

What does F3E1 say on a top-load?

The page asks “Did you receive a F3 E1 water level alert?” and says the alert indicates the washer can’t detect the water level, with a possible issue in the appliance control unit or associated wiring.

Read the supporting manual

How does it differ from F3E2?

On the top-load tree F3E2 is the hoses-reversed code, with a check that hot and cold valves are fully open.

Read the supporting manual

The manual behind the message.

Manufacturer document

F3 E1 - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-11-19; PH 14603 / PH 14603 (front-load washer)

Manufacturer document

F3E1 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13438 / PH 13438 (top-load washer)

Manufacturer document

F3E2 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13439 / PH 13439 (top-load washer)

The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14603 (front-load), PH 13438 (top-load), with the top-load F3E2 page.

Here to help

Good questions.
Clear answers.

Talk to our team
What is a water level alert on a top-load washer?

Maytag says the F3E1 alert indicates the washer cannot detect the water level. The page points to the appliance control unit or the associated wiring as the possible issue.

Does F3E1 mean there is no water coming in?

Not necessarily. The page speaks of detecting the water level, not of the supply. It is still sensible to confirm both faucets are open before you reset.

Is the control board the cause of F3E1?

It is one possibility. The page lists the appliance control unit or the associated wiring and gives no test, so a technician has to confirm which one it is.

How long should the reset take for F3E1?

Five minutes. Unplug the washer, or switch off its breaker, for 5 minutes, then restore power and watch the first fill.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.