Maytag washer F3E2 / Water and drain

Maytag washer
error code F3E2

Washer / display reference

On a top-load washer, F3E2 can mean the hot and cold inlet hoses are swapped. Check the hoses, make sure both valves are fully open, and reset for 5 minutes. The front-load page prints only the reset.

Also printed as F3E2

Last reviewed

Washer / display reference
Meaning
On a top-load washer, F3E2 can mean the hot and cold inlet hoses are swapped. Check the hoses, make sure both valves are fully open, and reset for 5 minutes. The front-load page prints only the reset.
Who handles it
Reset, then book
Related codes
Source
F3 E2 - Front Load Washer - Product Help | Maytag

What Maytag washer F3E2 means.

What it means

On a top-load washer, F3E2 can mean the hot and cold inlet hoses are swapped. Check the hoses, make sure both valves are fully open, and reset for 5 minutes. The front-load page prints only the reset.

What you can safely check

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

When to call a technician

F3E2 returns with correct hoses and open valves.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag washer F3E2: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Look at the hose connections

    Cold should go to the cold inlet and hot to the hot inlet.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Open both valves fully

    Both hot and cold inlet hoses must be connected for the washer to operate correctly.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Reset for 5 minutes

    Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Run a cycle

    See whether F3E2 returns.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Know your tree

    The hose explanation is on the top-load page.

Does F3E2 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does F3E2 say on a top-load?

The page asks “Are the hoses reversed?” and “Is the water turned on?” and says the code appears when the cold water hose is connected to the hot inlet and the hot hose to the cold inlet.

Read the supporting manual

Which other codes share the hose swap?

F0E4 lists a too-hot water temperature and tells you to check the hoses. F8E6 words it as no hot water detected, and reversed hoses are listed.

Read the supporting manual

The manual behind the message.

Manufacturer document

F3 E2 - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-11-19; PH 14604 / PH 14604 (front-load washer)

Manufacturer document

F3E2 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13439 / PH 13439 (top-load washer)

Manufacturer document

F0E4 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13426 / PH 13426 (top-load washer)

Manufacturer document

F8E6 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13460 / PH 13460 (top-load washer)

The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14604 (front-load), PH 13439 (top-load), with the F0E4 and F8E6 top-load pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Can hoses really be swapped?

Yes, and Maytag lists it first.

Where are the inlets?

On the back of the washer.

Does F3E2 mean no water?

It can, if a valve is closed.

Same on a front-load?

The page gives no cause.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.