Start from the symptom
Maytag washer leaking water.
Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Inlet hose ends
Both ends of each inlet hose need a hose washer and a tight connection, at the wall and at the washer.
- 2
Household drain
The sink and drainpipe must carry at least 17 gallons (64 L) of water per minute. A slow or clogged drain can back water out.
- 3
Hoses and plumbing
Look for cracks on every external hose, and check the laundry tub, faucets, drainpipe, water heater and pipes for their own leaks.
- 4
Top-load: water level
Adding clothes after the cycle has started can raise the level over the inner tub on the highest setting. Add no more than one or two small items.
- 5
Front-load: detergent and bulk dispenser
Use HE detergent only, since excess suds can leak. Make sure the bulk dispenser at the base, on models that have one, is fully closed.
Systems a technician may investigate.
These parts tie in to the symptom. Noticing it does not prove that any single one has worn out.

Washer drain hose (F9E1, drn, Ld)
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.

Washer door seal (bellows)
The door seal, or bellows, on a Maytag front-load washer can trap small items, dirt and pet hair, and then hold water. Product Help says to inspect and clean it monthly and to run the Clean Washer cycle monthly. Its small drain holes can clog and slow draining.
If the display adds a code.
Water and drain
For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Display and signals
Maytag's front-load washer page words SUD like this: “Sud or Sd is displayed:.” No reset is printed for it, so schedule a visit if it keeps appearing.
Read the related care guide.

Water still in the washer after the cycle: where it sits matters.
Where the water sits tells you what to do. A little in the dispenser area is normal, and more than half an inch after a thorough drawer cleaning is a service call. Water under the door seal usually means trapped lint, hair or small items, so clean the bellows monthly. Water in the tub with wet clothes points to an unbalanced load or a low spin, and Drain and Spin fixes that. [1][2][3][4]

A top-loader that will not agitate or spin: start with the load and the lid.
A Maytag top-load washer that stops agitating or spinning is most often reacting to the load or the setup, not to a broken part. Check balance, the cycle choice, the drain hose and standpipe, the level of the cabinet, a recent power cut, and anything resting on or under the lid. If dU or LdL stays on after that, book a technician. [1][2][3][4]
When observation becomes a service request.
Leave internal testing to a technician.
A hose or fitting still drips after being tightened.
You see a crack in a hose, or the leak seems to come from the cabinet itself.
Water appears at the front or top of the washer and the door seal is clean.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag washer leaking water advice. Read the manual for your own model.
- Leaking Water Underneath - Washer - Product Help | Maytag
- Leaking from Underneath or Bottom - Front Load Washer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Why is there water under my Maytag washer?
Product Help puts loose or washerless inlet hose connections first, then a slow household drain and damaged external hoses. Tighten the connections and look the hoses over before running another load.
Can suds cause a washer to leak?
Yes. In front-load models Maytag ties excess suds from regular detergent, or from too much of any detergent, to leaks, slow draining and weak rinsing. Thickened easy-pour bleach can foam too.
My top-load washer overflowed after I added clothes. Is that normal?
It can happen. On the highest water level, items added after the cycle starts raise the water over the inner tub. Add no more than one or two small items to a running wash.
Should I keep using a leaking washer?
Stop the cycle if water keeps reaching the floor, turn off the supply valves, and book a technician. A drain that cannot take 17 gallons a minute is worth fixing before the next load.
Maytag codes, symptoms, parts and service
From the message to what you do next.
F8E3
For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Maytag washer not draining
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Washer drain hose (F9E1, drn, Ld)
F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.
Washer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.