Troubleshooting

A top-load washer that stops agitating or spinning

A Maytag top-load washer that stops agitating or spinning is most often reacting to the load or the setup, not to a broken part. Check balance, the cycle choice, the drain hose and standpipe, the level of the cabinet, a recent power cut, and anything resting on or under the lid. If dU or LdL stays on after that, book a technician. [1][2][3][4]

An open top-load washer with clothes bunched to one side of the basket, a plaid blanket and a plastic basket on a shelf.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • An off-balance load can slow the spin, add noise and stretch the cycle; the washer tries to correct by refilling and rocking gently. 2
  • A low-water cycle on bulky items can leave clothes too buoyant to agitate. 1
  • The standpipe must stay between 39 and 96 inches. 2
  • Pause to add a garment only while the Add a Garment light is on. 2
  • dU points to objects on the lid; LdL points to a lid that is not locking. 34

Is the load the reason the basket will not move?#

Often it is. Maytag explains that clothes spread unevenly when the spin begins can shake the basket, slow the spin, lengthen the cycle and leave laundry wet. In a bad case the washer stops spinning until you redistribute the load by hand. 2

The washer does try to help itself. When it senses an out-of-balance load, it refills and turns the basket gently back and forth to spread the clothes. If that fails, it shows an error message. 2 Our pages on OFb and oL cover the two messages tied to a poorly spread or oversized load.

Signs of a lopsided wash, per the same page, are loud noise during the spin, heavy shaking and clothes that are still wet at the end. 2 Open the lid, move the pile so it sits evenly around the basket, close the lid and restart.

Clothes lie spread around the central agitator inside an open top-load washer, below the top row of holes.
Spread the load around the basket before restarting. 2

Why would a washer not agitate when the water is running?#

Cycle choice is the other cause on Maytag's page. A low-water cycle used for items that need a deep fill, such as bulky laundry, can leave clothes unable to move properly. Pick a cycle that raises the water level, such as Bulky. 1

Maytag adds a caution that cuts the other way: extra water added on top of a normal cycle can make clothing float, which stops it agitating and dilutes the detergent. Not every model offers every cycle; your Owner's Manual lists yours. 1

This is the same reasoning behind a rule on the not-spinning page: bedding, sheets, heavy coats and blankets belong on the Bulky or Sheets/Bedding cycle, not Normal or Rapid Wash. 2

What makes laundry come out wet after a spin?#

Several settings and habits do: a Low Spin or No Spin choice, bulky items on a normal cycle, a mid-cycle pause outside the Add a Garment window, and water still sitting in the tub. Each has a plain fix on Maytag's not-spinning page. 2

What happenedWhat Maytag suggests
Low Spin or No Spin was chosenUse the recommended spin for the garment, or select Drain & Spin 2
Bedding or bulky items on NormalUse Bulky or Sheets/Bedding 2
Washer paused after the Add a Garment light went outAdd items only while the light is on; touch and hold START/PAUSE to resume 2
Power failed during the spinThe washer may not reach full spin speed 2

Rearrange the load before choosing Drain & Spin, so the weight sits evenly. 2

What should I check in the drain hose, standpipe and floor?#

When water stands in the tub, inspect the hose, the standpipe and the level. Use the U-shaped hose form, keep only 4.5 inches of hose in the standpipe, leave the opening untaped, and keep the standpipe between 39 and 96 inches. 2

A standpipe taller than 96 inches stops the washer pumping water out properly, and water can flow back in. The hose also must not be kinked or clogged; straighten it, and clear any blockage in the utility sink's drainpipe. 2

The washer has to be level too. Maytag says an unlevel cabinet unbalances the load, which stops the machine spinning correctly and adds noise and vibration, especially in the spin. 2 A phone-based level app is the quick way to check.

A ribbed gray drain hose with a smooth U-shaped bend hooked into a white standpipe behind a top-load washer.
A U-shaped hose form, 4.5 inches inside the pipe, no tape. 2
  1. 1

    Straighten the drain hose#

    Remove any kink and clear a blockage in the drainpipe. 2

  2. 2

    Fit the U-shaped form#

    Attach the hose securely to the standpipe or tub. 2

  3. 3

    Measure what goes in#

    No more than 4.5 inches of hose should sit in the standpipe. 2

  4. 4

    Leave the opening uncovered#

    Do not tape over the drain opening. 2

  5. 5

    Level the washer#

    Adjust until the cabinet does not rock and the basket spins evenly. 2

The drain hose entry names the part, while the washer not draining page covers a tub that will not empty.

What do dU and LdL mean for the lid?#

dU means the washer found objects on the lid keeping it from unlocking. LdL means the lid is not locking. For dU, take a laundry basket or anything else off the top. For LdL, check for items under the lid and for detergent build-up. 34

Maytag's LdL page adds a clear next step: if the code appears again, schedule service. 4 That applies to dU as well, once the lid is clear and the code still returns. Our pages on dU and LdL carry the wording Maytag prints, and the door lock entry names the part involved.

A wicker laundry basket full of towels and clothes rests on the closed lid of a top-load washer.
For dU, clear the lid first. 3

What if I added clothes mid-cycle or the power went out?#

Add items only while the Add a Garment light is on. Pausing later can stop the washer reaching its top spin speed. With the light lit, pause, open the lid, add the item and touch and hold START/PAUSE to continue. A power failure during the spin can have the same effect. 2

Both situations leave clothes wetter than you expect, and neither calls for a repair. Maytag's page also says that Drain & Spin removes extra water from a load, after the load has been rearranged so the weight is spread evenly. Run that cycle once before assuming anything has failed. 2

In what order should I work through the checks?#

Go from the cheapest look to the most involved one. Maytag's two cycle-concern pages hold the same themes, so the order below simply puts them in the sequence that costs you the least time. 12

  1. Open the lid and look at the load: is it bunched, or too heavy for the cycle?
  2. Check the cycle against the laundry, and the spin setting against what you wanted.
  3. Look for objects on or under the lid if a code reads dU or LdL.
  4. Straighten the drain hose and look at the standpipe height.
  5. Check that the cabinet is level.
  6. Think back to the last few minutes before it stopped: a pause, a power cut, a very heavy load.

Write down which of these you changed, so that if the problem returns you can tell us exactly what you ruled out.

Which details help the technician?#

Describe when the basket stopped, what the clothes looked like, which cycle ran, whether the display showed dU or LdL, and whether the hose, standpipe and level checks were done. A power cut mid-spin is worth mentioning too.

  • Did the basket fail to agitate, to spin, or both?
  • Which cycle and spin speed were chosen?
  • Was anything on or under the lid?
  • How tall is the standpipe, and how far does the hose go in?
  • Did a code show, and how often?

Models we handle are listed on the washer repair page.

Sources#

  1. Not Agitating - Washer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text, out of balance and correct cycle sections
  2. Not Spinning - Washer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text, balance, wet clothes, standing water, level and power failure sections
  3. dU - Error Code - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · PH 13153; dateModified 2024-07-03 · article text, Are there items on the lid?
  4. LdL - Error Code - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · PH 13152; dateModified 2024-07-03 · article text, Is your washer lid locking?

Here to help

Good questions.
Clear answers.

Talk to our team
What makes a top-loader stop partway through a wash?

Two causes lead Maytag's pages: a load that is out of balance, and a cycle with too little water for the clothes to move, such as a low-water cycle on bulky items. Rebalance the load or choose Bulky for heavy laundry. [1]

Does dU mean the lid lock has broken?

Not necessarily. Maytag's page for dU says the washer found objects on the lid that keep it from unlocking. Lift off a laundry basket or anything else resting on top and see whether the lid releases. [3]

What does LdL tell me?

The lid is not locking. Maytag suggests looking for an item directly under the lid and for detergent build-up around the lock mechanism. If LdL comes back, schedule service. [4]

How tall may the standpipe be on a top-load Maytag?

Between 39 and 96 inches. Maytag's page says the washer cannot pump water out properly if the standpipe goes above 96 inches, and water may flow back into the machine. [2]

Can adding a sock mid-wash affect spin speed?

Yes, if you pause late. Maytag says to add items only while the Add a Garment light is on, because pausing later in the cycle can stop the washer reaching its top spin speed. [2]

Let’s take care of it.

A full hamper waits for no one.
Book the repair.