Troubleshooting

A dryer that tumbles and stays cold

When a Maytag electric dryer tumbles with no heat, check the household supply before the machine: both breakers of its 30-amp, 240-volt circuit, the power cord and the terminal screws. An L2 or F4 E4 code points the same way, and a five-minute breaker reset is the step Maytag gives. F4 E1 names the heater or its relays and uses a one-minute reset. [1][2][3][4]

A hand rests inside the empty drum of an open dryer, an open breaker panel on the wall behind it.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • The empty test is a heated timed cycle for 5 minutes, then feel inside. 1
  • The 30-amp circuit has a breaker pair, and one tripped side can leave the drum turning with no heat. 1
  • A 240-volt supply is required, and the cord and terminal screws should be checked with the dryer unplugged. 1
  • L2 and F4 E4 both report low or no line voltage that keeps the heater off. 23
  • F4 E1 names the heater or heater relays. 4

How do I tell a cold dryer from a slow one?#

Run a quick test. Choose a heated timed cycle, let it run empty for 5 minutes, then open the door and feel inside. If it is warm, heat is not the issue, and Maytag points you to its drying-performance advice instead. A cold drum means keep reading. 1

Check the selection before concluding the dryer has failed. Maytag's page notes that Air Only, also labeled Air/Fluff Only, never adds heat, by design. It exists for items that shrink easily, and it is handy with a drying rack for sweaters or shoes. It works better as a Timed Dry cycle. 1

A hand rests flat on the inside wall of an empty open dryer drum to feel for warmth.
Five minutes, heated, empty: then feel the drum. 1

Why do two breakers matter on an electric dryer?#

An electric Maytag expects a dedicated 30-amp circuit, fused on both legs, which means a pair of breakers. One leg runs the motor behind the drum while the other supplies the heater, so one tripped leg gives you tumbling without warmth. 1

That explains an old household puzzle: the dryer starts, the clothes tumble, and yet nothing dries. Maytag's instruction is simply to confirm that neither of the two breakers serving the dryer has tripped. If one trips again straight after a reset, stop and arrange a visit instead of resetting it again and again.

A hand rests on a pair of linked breaker switches in an open household breaker panel, a washer and dryer behind.
Two breakers serve one electric dryer. 1

Our dryer heater relays entry describes the part that switches the heater on, which is where the heat path continues past the panel.

What does the power supply need to look like?#

Maytag requires a 240-volt supply for an electric dryer, and says it will not operate correctly without one. Make sure the power cord is installed properly, per the installation instructions, and that the terminal screws at the dryer are tight, unplugging the dryer before touching them. 1

The page leans on a qualified electrician for the household side: if you do not have 240 volts, that is where to go. 1 The dryer's own installation instructions show both the 3-wire and the 4-wire cord arrangements, so match what you see at the back to what yours calls for.

A hand holds a heavy black three-prong dryer plug beside a matching wall outlet, unplugged.
Unplug before looking at terminals. 1
  1. 1

    Unplug the dryer#

    Pull the plug before checking the terminal screws. 1

  2. 2

    Confirm the cord matches the install instructions#

    Maytag shows 3-wire and 4-wire arrangements. 1

  3. 3

    Check that the terminal screws are tight#

    Loose terminals at the dryer are on Maytag's list. 1

  4. 4

    Plug in, restore the breakers and run the empty test again#

    Heated timed cycle, 5 minutes, then feel inside. 1

What do L2 and F4 E4 tell me?#

Both report low or no line voltage, which keeps the heater from turning on. Maytag says the supply at home may be the cause. With L2 showing, the dryer carries on running, and a touch on any pad removes the code and brings back the time remaining. 23

The reset Maytag prints for both is the same:

  1. 1

    Switch the breakers off#

    Leave them off for 5 minutes. 23

  2. 2

    Switch them back on#

    Restore the dryer's breakers. 23

  3. 3

    Start a timed dry cycle#

    Choose a timed dry setting. 23

  4. 4

    Watch for 5 minutes#

    Make sure the code does not come back. 23

If the code returns, or heat is still missing, the household circuit or the cord is the next place to look, and that is work for a technician or an electrician. Our pages on L2 and F4E4 repeat what Maytag prints, including where its commercial-grade residential dryer pages differ.

What does F4 E1 point to?#

F4 E1 is titled Heater System on Maytag's page, which points to the heater or its relays. It uses a shorter reset: breakers off for 1 minute, back on, a timed dry cycle, and one minute of watching for the code. 4

Unlike L2 and F4 E4, this page names no household-supply check. A return of F4 E1 after the one-minute reset is therefore a cue to arrange a visit instead of resetting again. Our F4E1 page notes that the commercial-grade residential dryer page words it differently.

What if it does heat but still dries slowly?#

Then the problem has moved from supply to airflow or settings, and Maytag points you to its drying-performance guidance. The usual suspects are the lint screen, the vent run, the exhaust hood, the cycle and the level of the cabinet. 56

Start with the lint screen: clean it after every load, and clean off the residue that builds up on it if you use fabric softener regularly. To test the vent, put your palm under the outdoor hood once the dryer has been working 5 to 10 minutes. Airflow weaker than a hair dryer on high means lint needs clearing along the full run and at the hood. 6

The hood must sit at least 12 inches off the ground or from anything that could block it, such as bushes or snow, and the vent should be 4-inch rigid or flexible metal, as straight and short as possible. Foil or plastic can collapse. 5 Maytag says the home venting should be cleaned every one to two years, or sooner when drying slows. 56

An unlevel dryer can keep clothes from touching the moisture sensors on automatic cycles, and an EcoBoost option, where fitted, adds about 40 minutes by using slightly less heat. 56 Our moisture sensor entry describes the sensor.

A restricted vent also has its own message. F4 E3 reports restricted airflow, and Maytag says the dryer keeps running while it is displayed; touch any key to clear it, then check the lint screen, the run to the wall and the hood. If it persists, have the entire venting run cleaned. 7 Our F4E3 page repeats the wording.

Why does the order of these checks matter?#

Each check is cheaper and safer than the next. Supply comes before anything inside the cabinet, because two of Maytag's three codes name the household supply as the likely source. 23

Running the empty test first also tells you whether you have a heat problem or an airflow problem, and the answer sends you to a different section of this guide. 15

If you do reset a breaker pair, keep a clock nearby. The five-minute and one-minute waits are part of the procedure, not suggestions, and cutting a wait short is the usual way a code seems to return at once. 234

What helps the technician?#

Share whether the empty test was warm or cold, whether either breaker tripped, how the cord is wired, and the exact code. Note whether the dryer kept running with the code and how long the breakers stayed off.

  • Warm or cold after 5 minutes, empty?
  • Both breakers on, and did either trip again?
  • 3-wire or 4-wire cord?
  • Which code, and does touching a pad clear it?
  • Is the vent clear and short? (Our exhaust vent entry covers that part.)

Our Maytag dryer work is listed on the dryer repair page.

Sources#

  1. Not Heating - Electric Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text: heating test, Air Only, circuit breakers, power supply cord
  2. L2 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · PH 12837; dateModified 2025-05-27 · article text: home power supply, circuit breakers, Cycle Power
  3. F4 E4 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · PH 12812; dateModified 2025-05-27 · article text: home power supply, circuit breakers, Cycle Power
  4. F4 E1 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · PH 12810; dateModified 2026-08-19 · article text: F4 E1 Heater System
  5. Long Dry Times - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text: heating test, vent, lint screen, exhaust hood, level, EcoBoost
  6. Not Drying - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text: lint screen, exhaust airflow test, level, dryness level
  7. F4 E3 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text: Is the Lint Screen or Vent Clogged?

Here to help

Good questions.
Clear answers.

Talk to our team
Why does an electric Maytag dryer need two breakers?

The dryer is fed by a dedicated 30-amp circuit that is fused on both legs, so it has a pair of breakers. One leg powers the drum motor, the other the heating element, and a single tripped leg leaves the drum turning without heat. [1]

What is the quickest way to prove the drum is heating?

Choose a heated timed cycle, run it empty for 5 minutes, open the door and feel inside. If it is warm, the problem is drying performance rather than heat, and Maytag points to its drying-performance guidance. [1]

Does the Air Only setting heat the drum?

No. Maytag says Air Only, or Air/Fluff Only, adds no heat at any point in the cycle. It suits shrink-prone items, sweaters on a rack or shoes, and works best with Timed Dry. [1]

An L2 showed up and the dryer kept running. Is that expected?

Yes. Maytag says the dryer continues to run with L2 on, since L2 reports low or no line voltage that keeps the heater from turning on. A touch on any pad removes it from the display. [2]

How long should the breakers stay off when resetting after F4 E4?

Five minutes. Turn the breakers off for five minutes, switch them on, run a timed dry cycle and keep watching for five more minutes. For F4 E1, Maytag's page asks for one minute at each step. [3][4]

Let’s take care of it.

A full hamper waits for no one.
Book the repair.