Inside the appliance
Dryer moisture sensor (F3E2, F3E5). In plain English.
On a Maytag dryer, F3E2 happens when five loads in a row are dried without the moisture sensor registering data. Press Power to clear it. Product Help asks whether the dryer is level and whether a small load or single item missed the sensors. F3E5 is also listed as a moisture sensor code.

Where it fits.
Dryer moisture sensor (F3E2, F3E5) in the appliance
Inside the dryer drum, where clothes touch the sensors as they tumble.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Dryer moisture sensor (F3E2, F3E5) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag dryer will not start
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.

Maytag dryer making noise
Thumping, buzzing, knocking and squealing each point somewhere different on a Maytag dryer. New rollers and a flat spot after time off thump and fade by themselves. Pockets, items in the lint chute and a washer next door cause the rest. Squealing from an older dryer can mean a worn belt or pulley.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Press Power
Pressing Power clears the code and lets you restart.
- 2
Level the dryer
A dryer that is not level may keep clothes from touching the sensors. Check from the cabinet edge, as the top can be curved.
- 3
Add to the load
A very small load or a single item may not touch the sensors. Dry larger loads, or use an Automatic cycle instead of Timed Dry.
- 4
Power cycle
If it persists, cut the breaker for a minute, restore it, and start a timed dry.
Cleaning or replacement?
Leave internal testing to a technician.
F3E2 comes back after leveling and a full load.
Loads run long or stop early on Automatic cycles.
The code appears every few loads.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Dryer moisture sensor (F3E2, F3E5) advice. Read the manual for your own model.
- F3 E2 - Error Code - Commercial Dryer - Product Help | Maytag
- F3 E2 - Error Code - Dryer - Product Help | Maytag
- F3 E5 - Error Code - Dryer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
What triggers F3E2?
Five consecutive loads without the moisture sensor registering data, per the Product Help page.
Will a timed cycle avoid it?
Product Help suggests an Automatic cycle for small loads so the sensors engage, not Timed Dry.
Does F3E5 mean the same?
It is labeled moisture sensor too. The dryer page lists the title only; the commercial-grade page adds a five-minute breaker reset.
How do I check level?
Use a level on the cabinet edge and turn the dryer feet, since the top can be curved.
Maytag codes, symptoms, parts and service
From the message to what you do next.
F3E2
F3E2 on a Maytag commercial-grade residential dryer is explained as “F3E2 - Moisture Sensor.” Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Maytag dryer will not start
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.
Dryer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.

