Start from the symptom
Maytag dryer will not start.
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Two breakers, not one
An electric dryer uses two household fuses or breakers. Confirm both are intact and tight, and reset any tripped breaker.
- 2
Power supply cord and 240 volts
A cord installed wrong, or loose terminal screws at the dryer, can stop it starting or heating. Unplug the dryer before checking the screws, and ask an electrician to confirm 240 volts.
- 3
Control Lock
If the Control Lock light is on, the controls ignore touch. Hold the Control Lock button down for 3 seconds and its light goes out.
- 4
Press and hold Start
Start, Push to Start and Hold to Start need a press of two to five seconds. Dry your hands and the panel, and touch with a fingertip.
- 5
Door, latch and cycle
Push the door until it latches; two-latch models need both secure. Clear the latch of packing or clothing. Some models will not start on the Wrinkle Shield option.
Systems a technician may investigate.
We pick the part after we read the model label and test the unit. Nothing is ordered ahead of time, and the quote is yours to approve before any work begins.

Dryer moisture sensor (F3E2, F3E5)
On a Maytag dryer, F3E2 happens when five loads in a row are dried without the moisture sensor registering data. Press Power to clear it. Product Help asks whether the dryer is level and whether a small load or single item missed the sensors. F3E5 is also listed as a moisture sensor code.

Dryer heater and relays (F4E1)
F4E1 on a Maytag dryer names the heater or the heater relays as the likely problem. Product Help gives a one-minute breaker reset, then a timed dry cycle while you watch the dryer for one minute. For no heat, run a heated timed cycle for five minutes and feel inside.

Dryer lint screen and exhaust vent (F4E3, AF)
Long dry times on a Maytag dryer often trace to airflow. F4E3, AF and Check Vent all say the lint screen or vent is clogged, crushed, kinked or has too many turns. Product Help wants the lint screen cleaned after every use and the home venting every one to two years.
If the display adds a code.
Display and signals
Loc on a Maytag dryer is explained as “The Loc Error code indicates that the Control Lock has been enabled.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Reset only
The Maytag page for F1E1 on a Maytag commercial-grade residential dryer or dryer stops at a reset and leaves the cause unstated. To reset it, leave the circuit breaker off for 5 minutes before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
Power supply
On a commercial-grade residential dryer, the entry for PF says “A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure.” Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Read the related care guide.

A dryer that tumbles but never warms: check the supply before the machine.
When a Maytag electric dryer tumbles with no heat, check the household supply before the machine: both breakers of its 30-amp, 240-volt circuit, the power cord and the terminal screws. An L2 or F4 E4 code points the same way, and a five-minute breaker reset is the step Maytag gives. F4 E1 names the heater or its relays and uses a one-minute reset. [1][2][3][4]

A code on your dryer: vent, supply or reset?
On a Maytag dryer, group the codes by the first thing each one wants. F4 E3 and the AF or Check Vent light mean airflow: clean the lint screen and vent. F4 E4 and L2 mean the household supply: check both breakers. F1 E1, F3 E3, F4 E1 and F6 E1 mean a breaker reset. PF means the cycle was cut short by a power failure. [1][3][4][5][6][7][8]
When observation becomes a service request.
Leave internal testing to a technician.
The drum light and controls stay dark after both breakers check out.
The dryer shows no power, or a breaker trips again right away.
It runs but the drum does not turn.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag dryer will not start advice. Read the manual for your own model.
- Not Starting or Not Operating - Dryer - Product Help | Maytag
- No Power - Electric Dryer - Product Help | Maytag
- Not Tumbling or Spinning - Dryer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Why does my Maytag electric dryer have no power?
Product Help starts with the household fuses or breakers. An electric dryer uses two, so check that both are intact, then check the supply cord and terminal screws, with the dryer unplugged.
How long do I hold the Start button?
Two to five seconds on Start, Push to Start or Hold to Start. A wet panel or wet hands can stop a touch control from registering, so dry both.
The dryer is on but nothing happens. What next?
Look for the Control Lock light, a door that has not latched all the way, and a Wrinkle Shield setting where the cycle knob needs Automatic Dry, Accudry or Time Dry. Then book a technician.
Is a 240-volt problem something I can fix?
No. Product Help tells you to check with a qualified electrician. If the power cord needs work, unplug the dryer first and follow the install instructions.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Loc
Loc on a Maytag dryer is explained as “The Loc Error code indicates that the Control Lock has been enabled.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag dryer will not start
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.
Dryer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.