Inside the appliance
Dryer heater and relays (F4E1). In plain English.
F4E1 on a Maytag dryer names the heater or the heater relays as the likely problem. Product Help gives a one-minute breaker reset, then a timed dry cycle while you watch the dryer for one minute. For no heat, run a heated timed cycle for five minutes and feel inside.

Where it fits.
Dryer heater and relays (F4E1) in the appliance
Product Help does not say where the heater sits on your model.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Dryer heater and relays (F4E1) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag dryer will not start
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.

Maytag dryer making noise
Thumping, buzzing, knocking and squealing each point somewhere different on a Maytag dryer. New rollers and a flat spot after time off thump and fade by themselves. Pockets, items in the lint chute and a washer next door cause the rest. Squealing from an older dryer can mean a worn belt or pulley.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Test the heat
Run a heated timed cycle for 5 minutes with the dryer empty, then open the door and feel inside.
- 2
Rule out Air Only
Air Only or Air/Fluff adds no heat at any time.
- 3
Check the breakers
An electric dryer uses two breakers or fuses and needs a 240-volt supply. Both must be on.
- 4
Reset power
Breaker off for a minute, then on, a timed dry cycle, and a minute of watching.
Cleaning or replacement?
Leave internal testing to a technician.
F4E1 returns after the reset.
The dryer tumbles but never gets warm.
A breaker trips or a fuse blows when it starts.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Dryer heater and relays (F4E1) advice. Read the manual for your own model.
- F4 E1 - Error Code - Commercial Dryer - Product Help | Maytag
- F4 E1 - Error Code - Dryer - Product Help | Maytag
- Not Heating - Electric Dryer - Product Help | Maytag
- No Power - Electric Dryer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
What does F4E1 mean?
The commercial-grade residential dryer page names the heater or heater relays. The standard dryer page titles it Heater System.
Does my electric dryer need 240 volts?
Yes, per Product Help. If you do not have 240 volts, it will not operate correctly. Ask a qualified electrician.
How do I test if it is heating?
Run a heated timed cycle for 5 minutes empty, open the door and feel inside.
Can I fix the heater myself?
Product Help prints no home steps beyond the breaker reset. A dryer that stays cold needs a technician.
Maytag codes, symptoms, parts and service
From the message to what you do next.
F4E1
Maytag lists the heater or the heater relays for F4E1 on the commercial-grade residential dryer. Reset the power first and watch the display; a returning the code is the cue to book us.
Maytag dryer will not start
A Maytag dryer that does nothing is usually a power, lock or latch issue before it is a broken part. An electric dryer draws on two breakers or fuses and needs 240 volts, the Control Lock may be on, and the door may look shut without latching. Check these, then book a technician.
Dryer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.

