Model-specific code library

Maytag washer Water and drain codes

30 printed codes in this group: dET, Detergent Level Indicator, Detergent Level Indicator Light, Detergent Low, drn, F0E2, F0E4, F0E8, F20, F21 and 20 more.

Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Water and drain codes

dET

On a front-load washer, dET means the detergent dispenser cartridge is not detected. If you use single-load doses of detergent, you can ignore the message. Otherwise seat the cartridge fully and close the drawer completely.

Owner checks first
Detergent Level Indicator

Detergent Level Indicator on a Maytag front-load washer is explained as “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” Nothing else is printed, so schedule a visit if it repeats.

Information only
Detergent Level Indicator Light

The Maytag page for Detergent Level Indicator Light on a front-load washer states “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” Nothing else is printed, so schedule a visit if it repeats.

Information only
Detergent Low

For a front-load washer showing Detergent Low, Maytag prints “Detergent Low will flash on the display when more detergent needs to be added to the bulk dispenser.” Nothing else is printed, so schedule a visit if it repeats.

Information only
drn

The Maytag page for drn on a top-load washer states “If F9 E1 (drain pump system problem-long drain) appears in the display, the washer is taking too long to...” No reset is printed for it, so schedule a visit if it keeps appearing.

Technician visit
F0E2

Maytag's front-load washer page words F0E2 like this: “The F0 E2 error code means your washer has detected excessive suds in the washer basket.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.

Owner checks first
F0E4

F0E4 is “Water Temperature” on both Maytag washer trees: the washer senses the water temperature is too hot. Verify the water hoses are installed correctly and switched between the hot and cold lines, then reset for 5 minutes.

Reset, then book
F0E8

The Maytag page for F0E8 on a top-load washer states “F0E8 - Water remains in tub.” No reset is printed for it, so schedule a visit if it keeps appearing.

Technician visit
F20

Maytag's front-load washer page words F20 like this: “F20 indicates a water inlet problem-no water or insufficient water supply.” Try the five-minute power-off reset, and schedule a visit if the code returns.

Reset, then book
F21

The Maytag page for F21 on a front-load washer states “F21 indicates a drain problem.” Try the five-minute power-off reset, and schedule a visit if the code returns.

Reset, then book
F3E1

On a top-load washer, F3E1 means the washer cannot detect the water level, and Maytag points to the appliance control unit or wiring. The front-load page prints only a reset. Cut power for 5 minutes and restart.

Reset, then book
F3E2

On a top-load washer, F3E2 can mean the hot and cold inlet hoses are swapped. Check the hoses, make sure both valves are fully open, and reset for 5 minutes. The front-load page prints only the reset.

Reset, then book
F3E5

On a top-load washer, F3E5 is headed “Mini Dispenser” with the note “Please add detergent manually.” The front-load page prints only a reset. Add detergent by hand, reset for 5 minutes, and book a visit if it returns.

Reset, then book
F8E1

On a front-load washer, the entry for F8E1 says “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.

Owner checks first
F8E2

F8E2 on a Maytag front-load washer is explained as “This indicates there is a problem with the Dispenser System.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.

Technician visit
F8E3

For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.

Reset, then book
F8E6

Maytag’s F8E6 page gives two possible meanings depending on the model: the lid is open during the soak cycle, or no hot water was detected. Close the lid; for hot water, check the hoses and valves. Then reset for 5 minutes.

Reset, then book
F9E1

F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.

Technician visit
FH

FH on a Maytag front-load washer is explained as “FH indicates that there is a water inlet problem, which is no or insufficient water supply.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.

Technician visit
Fill or Sensing Light On

The Maytag page for Fill or Sensing Light On on a top-load washer states “When the Start/Stop button is pressed and the Water Level knob is set to Auto Sensing, the washer will fill...” No reset is printed for it, so schedule a visit if it keeps appearing.

Information only
HC

On a top-load washer, the entry for HC says “If HC (hot and cold hoses reversed) appears in display, it means the hot and cold inlet hoses have been installed incorrectly.” No reset is printed for it, so schedule a visit if it keeps appearing.

Owner checks first
Ld

On a top-load washer, the entry for Ld says “If Ld(drain pump system problem-long drain) appears in the display, the washer is taking too long to drain...” Maytag prints no reset for it; if it keeps appearing, schedule a visit.

Technician visit
LF

For a top-load washer showing LF, Maytag prints “If F8 E1 or LF (long fill) appears in the display, the washer is taking too long to fill.” No reset is printed for it, so schedule a visit if it keeps appearing.

Owner checks first
Lid Lock is Flashing

For a commercial-grade residential washer showing Lid Lock is Flashing, Maytag prints “If F8 E1 or LF (too long to fill) appears in the display, the washer is taking too long to fill or the washer...” Nothing else is printed, so schedule a visit if it repeats.

Owner checks first

Let’s take care of it.

A full hamper waits for no one.
Book the repair.