Maytag washer F8E6 / Water and drain

Maytag washer
error code F8E6

Washer / display reference

Maytag’s F8E6 page gives two possible meanings depending on the model: the lid is open during the soak cycle, or no hot water was detected. Close the lid; for hot water, check the hoses and valves. Then reset for 5 minutes.

Also printed as F8E6

Last reviewed

Washer / display reference
Meaning
Maytag’s F8E6 page gives two possible meanings depending on the model: the lid is open during the soak cycle, or no hot water was detected. Close the lid; for hot water, check the hoses and valves. Then reset for 5 minutes.
Who handles it
Reset, then book
Related codes
Source
F8E6 - Error Code - Product Help | Maytag

What Maytag washer F8E6 means.

What it means

Maytag’s F8E6 page gives two possible meanings depending on the model: the lid is open during the soak cycle, or no hot water was detected. Close the lid; for hot water, check the hoses and valves. Then reset for 5 minutes.

What you can safely check

Power and water off before any panel comes off; towels down for spills.

When to call a technician

F8E6 returns with the lid closed and the hoses correct.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag washer F8E6: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Close the lid

    If the lid is open during the soak cycle, closing it resumes the cycle.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Check the hoses

    The page says reversed hot and cold hoses can cause it; reverse them and run another cycle.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Open both valves

    Hot and cold valves must be fully open.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Reset for 5 minutes

    Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Check your water heater

    No hot water detected may mean the supply is cold. This is our look.

Does F8E6 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

Why two meanings?

The page says that depending on the model, F8E6 could have two meanings: the lid is open during the soak cycle, or no hot water was detected.

Read the supporting manual

What does the hose advice say?

It says that if F8E6 is displayed, the hot and cold inlet hoses may be installed incorrectly, with cold on the hot inlet and hot on the cold inlet. Reverse the hoses and run another cycle.

Read the supporting manual

How does F8E6 relate to F3E2 and F0E4?

F3E2 lists the same hose swap. F0E4 senses the water as too hot and also tells you to check the hoses.

Read the supporting manual

Which meaning is mine?

Maytag does not say how to tell. If the lid is open, close it; if not, work through the water checks.

Read the supporting manual

The manual behind the message.

Manufacturer document

F8E6 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13460 / PH 13460 (top-load washer)

Manufacturer document

F3E2 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13439 / PH 13439 (top-load washer)

Manufacturer document

F0E4 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13426 / PH 13426 (top-load washer)

The Product Help pages list no models, so the text applies to the washer type, not to a named model. Source: Product Help PH 13460 (top-load), with the F3E2 and F0E4 top-load pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Does a soak cycle stop when the lid is open?

The page says that if the lid is open during the soak cycle, closing it resumes the cycle. That is the first of the two meanings it gives for F8E6.

Is F8E6 only a top-load code?

We cite the top-load page for it. The front-load tree has no F8E6 page in the sources we hold, so we do not describe it for front-load washers.

How long is the F8E6 reset?

Five minutes. Unplug the washer, or switch off its breaker, for 5 minutes, then restore power. Check the hoses and valves first if the meaning was no hot water.

Does the F8E6 page mention the water heater?

No. It lists reversed hoses, a closed valve and the 5-minute reset. If the hoses and valves are right, tell us how hot your supply runs.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.