What it means
Detergent Level Indicator on a Maytag front-load washer is explained as “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” Nothing else is printed, so schedule a visit if it repeats.
Maytag washer Detergent Level Indicator / Water and drain
Detergent Level Indicator on a Maytag front-load washer is explained as “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” Nothing else is printed, so schedule a visit if it repeats.
Also printed as Detergent Level Indicator
Detergent Level Indicator on a Maytag front-load washer is explained as “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” Nothing else is printed, so schedule a visit if it repeats.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
Detergent Level Indicator returns, or the front-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Check that your appliance is a front-load washer and copy Detergent Level Indicator exactly as the display shows it.

Maytag prints no reset for Detergent Level Indicator, so record what the washer does rather than guessing a fix.

Keep the model number close and note when Detergent Level Indicator appeared and what the front-load washer was doing.

Check the dispenser drawer or bulk tank of the front-load washer for clumps, build-up or an overfill.
Keep the model number close and note when Detergent Level Indicator appeared and what the front-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F8E2 on a Maytag front-load washer is a dispenser system problem, and Product Help wants you to confirm the drawer or cartridge is not clogged with detergent.
Read the definitionMaytag's front-load washer page gives Detergent Level Indicator a single line: “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” It adds nothing about cause.
Read the supporting manualMaytag's page for Detergent Level Indicator gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualBeeping and Audio Tones is a separate entry from Detergent Level Indicator on the front-load washer page, with its own wording.
Read the supporting manualThe front-load washer can still wash by hand-dosing detergent if the dispenser is the problem.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-03-26; PH 7124 / PH 7124 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-16; PH 13895 / PH 13895 (front-load washer)
Detergent Level Indicator comes from Maytag Product Help (PH 7124) for the front-load washer, read in November 2026; the Detergent Level Indicator entry names no models.
The help page states “Some models have an indicator light to show the status of the Load & Go™ Dispenser.” Nothing else is added.
Nothing is printed for it, so record the display and schedule us if Detergent Level Indicator continues.
Not by itself; the page stops at the line it prints.
The model and serial numbers, the exact display for Detergent Level Indicator, and what the front-load washer was doing at the time.
Maytag codes, symptoms, parts and service
On a front-load washer, the entry for Beeping and Audio Tones says “These sounds are cycle signal tones that are part of normal operation.” Nothing else is printed, so schedule a visit if it repeats.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
F8E2 on a Maytag front-load washer is a dispenser system problem, and Product Help wants you to confirm the drawer or cartridge is not clogged with detergent. On top-load models F8E2 is the bulk dispenser and F3E5 the mini dispenser. dET means the cartridge is not detected.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.