Maytag washer F0E4 / Water and drain

Maytag washer
error code F0E4

Washer / display reference

F0E4 is “Water Temperature” on both Maytag washer trees: the washer senses the water temperature is too hot. Verify the water hoses are installed correctly and switched between the hot and cold lines, then reset for 5 minutes.

Also printed as F0E4

Last reviewed

Washer / display reference
Meaning
F0E4 is “Water Temperature” on both Maytag washer trees: the washer senses the water temperature is too hot. Verify the water hoses are installed correctly and switched between the hot and cold lines, then reset for 5 minutes.
Who handles it
Reset, then book
Related codes
Source
F0 E4 - Front Load Washer - Product Help | Maytag

What Maytag washer F0E4 means.

What it means

F0E4 is “Water Temperature” on both Maytag washer trees: the washer senses the water temperature is too hot. Verify the water hoses are installed correctly and switched between the hot and cold lines, then reset for 5 minutes.

What you can safely check

Power and water off before any panel comes off; towels down for spills.

When to call a technician

F0E4 returns after the hose check and 5-minute reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag washer F0E4: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Look at the hose labels

    Hot goes to the hot inlet and cold to the cold inlet. The page says to verify they are installed correctly and not switched.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Open both valves

    The related F3E2 page says both hot and cold valves must be fully open. [3]

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Reset for 5 minutes

    Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Restart a short cycle

    See whether F0E4 returns during the first fill.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Note your water heater

    If the hoses are right, tell us how hot the supply runs. Maytag does not print a limit.

Does F0E4 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does F0E4 say?

The heading is “F0E4: Water Temperature.” The washer senses the water temperature is too hot, and you should verify the hoses are installed correctly and switched between the hot and cold lines.

Read the supporting manual

Do the two trees disagree?

No. The front-load and top-load pages print the same text, the same hose check and the same 5-minute reset.

Read the supporting manual

How is F0E4 different from F3E2?

The top-load F3E2 page says the cold hose connected to the hot inlet, and the reverse, will produce that code. F0E4 arrives at the same hose swap from a too-hot reading.

Read the supporting manual

What does the reset do?

Disconnecting power for 5 minutes resets the control. If the hoses are right and F0E4 returns, book a visit.

Read the supporting manual

The manual behind the message.

Manufacturer document

F0 E4 - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-11-19; PH 14593 / PH 14593 (front-load washer)

Manufacturer document

F0E4 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13426 / PH 13426 (top-load washer)

Manufacturer document

F3E2 - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-05-27; PH 13439 / PH 13439 (top-load washer)

The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14593 (front-load), PH 13426 (top-load) and the top-load F3E2 page.

Here to help

Good questions.
Clear answers.

Talk to our team
Can swapped hoses cause F0E4?

The page tells you to check for exactly that.

Does F0E4 mean the water heater is too hot?

The page says the washer senses the temperature is too hot, but its first check is the hoses.

How long do I wait?

5 minutes.

Does it matter if I have a top-load or front-load washer?

Not for F0E4; both pages match.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.