What it means
F0E5 is an unbalanced load on Maytag washers. The front-load page says a bulky item alone or a tightly packed load can lengthen the cycle and leave clothes dripping; the top-load page says cancel, drain, rearrange and restart.
Maytag washer F0E5 / Information
F0E5 is an unbalanced load on Maytag washers. The front-load page says a bulky item alone or a tightly packed load can lengthen the cycle and leave clothes dripping; the top-load page says cancel, drain, rearrange and restart.
Also printed as F0E5
F0E5 is an unbalanced load on Maytag washers. The front-load page says a bulky item alone or a tightly packed load can lengthen the cycle and leave clothes dripping; the top-load page says cancel, drain, rearrange and restart.
Power and water off before any panel comes off; towels down for spills.
F0E5 returns with a loose, balanced load.
Your Maytag to-do list, saved here on this device

The front-load page says if it is not dripping, the cycle finished as expected and just took longer to balance; no action needed.

Clothing should move freely. Remove a few items and run Drain & Spin.

Balance a rug or a jeans jacket with a few extra garments and run Drain & Spin.

Cancel the cycle, run a drain-only cycle if water is present, then rearrange or remove items.

The top-load page suggests one of those cycles for the next load.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
It is headed “Off Balance” and asks if the washer is overloaded or if a bulky item was washed by itself. A large unbalanced load can cause reduced spin speeds, longer cycle times and clothing still dripping wet.
Read the supporting manualIt is headed “Off-Balanced Load” and says the load is unbalanced or too large. It lists steps for when the error is present and for when the cycle can be paused.
Read the supporting manualPress Start to pause, open the lid, rearrange the clothing or reduce the load, and press Start again.
Read the supporting manualOn the front-load page it can be just a delay. If the load is not dripping wet, no action is needed.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14594 / PH 14594 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-07-01; PH 13427 / PH 13427 (top-load washer)
The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14594 (front-load) and PH 13427 (top-load).
No. Rebalancing is the fix on both pages.
It removes water after you rearrange the load.
F0E9 is an unbalanced load on top-load only, with a longer article.
Both trees advise balancing a single large item with other garments.
Maytag codes, symptoms, parts and service
F0E4 is “Water Temperature” on both Maytag washer trees: the washer senses the water temperature is too hot. Verify the water hoses are installed correctly and switched between the hot and cold lines, then reset for 5 minutes.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.