What it means
The top-load page defines F0E3 as an overload: the load is too heavy and the overload recovery cycle is running. The front-load page prints only a reset. Reload loosely and balanced; if it persists, call for service.
Maytag washer F0E3 / Information
The top-load page defines F0E3 as an overload: the load is too heavy and the overload recovery cycle is running. The front-load page prints only a reset. Reload loosely and balanced; if it persists, call for service.
Also printed as F0E3
The top-load page defines F0E3 as an overload: the load is too heavy and the overload recovery cycle is running. The front-load page prints only a reset. Reload loosely and balanced; if it persists, call for service.
Power and water off before any panel comes off; towels down for spills.
F0E3 returns with a lighter, balanced load.
Your Maytag to-do list, saved here on this device

The top-load page says the load is too heavy. Remove some items before you restart.

Place garments loosely and evenly around the basket wall, dry items only, and add only one or two garments after the washer has started.

Small items can get caught in a pump or between basket and tub, which can slow draining.

An unbalanced load can reduce spin speed and leave clothes wet.

On the front-load page the only step is to cut power for 5 minutes.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The page headed “F0E3 - Overload” says the load is too heavy and the overload recovery cycle is running. It refers you to the cycle guide and says to call for service if the problem persists.
Read the supporting manualIt prints the title and a power reset: disconnect the washer for 5 minutes, then reconnect. It names no cause.
Read the supporting manualThe top-load page asks for a balanced load that is not tightly packed, in loose heaps around the basket wall. A large unbalanced load can mean a reduced spin speed and wet clothes at the end.
Read the supporting manualThe page says small items can get caught in a pump or between the basket and tub and slow draining.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14592 / PH 14592 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-01-27; PH 13425 / PH 13425 (top-load washer)
The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14592 (front-load) and PH 13425 (top-load).
No. F0E3 is overload; F0E5 and F0E9 are balance codes.
Maytag gives no weight. It says to avoid a tightly packed basket.
On the front-load page that is the only step; on the top-load page, reload first.
The page says an overload recovery cycle is running.
Maytag codes, symptoms, parts and service
Maytag's front-load washer page words F0E2 like this: “The F0 E2 error code means your washer has detected excessive suds in the washer basket.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.