What it means
Maytag's front-load washer page words F0E2 like this: “The F0 E2 error code means your washer has detected excessive suds in the washer basket.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer F0E2 / Water and drain
Maytag's front-load washer page words F0E2 like this: “The F0 E2 error code means your washer has detected excessive suds in the washer basket.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as F0E2
Maytag's front-load washer page words F0E2 like this: “The F0 E2 error code means your washer has detected excessive suds in the washer basket.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Power and water off before any panel comes off; towels down for spills.
F0E2 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Match the label on your appliance to the front-load washer list before you rely on the wording for F0E2.

Maytag prints no reset for F0E2, so record what the washer does rather than guessing a fix.

Write down the model and serial numbers and the exact F0E2 wording before you call.

Open the front-load washer and spread the load evenly; very small or very heavy loads can unbalance a spin.
Note the model and the moment F0E2 showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
F0E2 is covered by this wording on the front-load washer page: “The F0 E2 error code means your washer has detected excessive suds in the washer basket.”
Read the supporting manualNo reset is printed for F0E2 on the front-load washer page. Writing down what the washer does around the code is the useful thing to do.
Read the supporting manualThe front-load washer list prints F0E3 next to F0E2, but with a different line. Look up the one on your display.
Read the supporting manualDo not wedge or hold the drum while it spins. If F0E2 keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14591 / PH 14591 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-02-14; PH 13424 / PH 13424 (top-load washer)
Facts for F0E2 are from the front-load washer table (PH 14591) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag's wording is “The F0 E2 error code means your washer has detected excessive suds in the washer basket.” That is the whole entry.
There is no reset on that page. Note what happens and book us if F0E2 persists.
Not by itself; the page stops at the line it prints.
The model and serial numbers, the exact display for F0E2, and what the front-load washer was doing at the time.
Maytag codes, symptoms, parts and service
The top-load page defines F0E3 as an overload: the load is too heavy and the overload recovery cycle is running. The front-load page prints only a reset. Reload loosely and balanced; if it persists, call for service.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.