What it means
For a front-load washer showing Detergent Low, Maytag prints “Detergent Low will flash on the display when more detergent needs to be added to the bulk dispenser.” Nothing else is printed, so schedule a visit if it repeats.
Maytag washer Detergent Low / Water and drain
For a front-load washer showing Detergent Low, Maytag prints “Detergent Low will flash on the display when more detergent needs to be added to the bulk dispenser.” Nothing else is printed, so schedule a visit if it repeats.
Also printed as Detergent Low
For a front-load washer showing Detergent Low, Maytag prints “Detergent Low will flash on the display when more detergent needs to be added to the bulk dispenser.” Nothing else is printed, so schedule a visit if it repeats.
Power and water off before any panel comes off; towels down for spills.
Detergent Low repeats after the reset.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Check that your appliance is a front-load washer and copy Detergent Low exactly as the display shows it.

Maytag prints no reset for Detergent Low, so record what the washer does rather than guessing a fix.

Write down the model and serial numbers and the exact Detergent Low wording before you call.

Check the dispenser drawer or bulk tank of the front-load washer for clumps, build-up or an overfill.
Write down the model and serial numbers and the exact Detergent Low wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F8E2 on a Maytag front-load washer is a dispenser system problem, and Product Help wants you to confirm the drawer or cartridge is not clogged with detergent.
Read the definitionMaytag's front-load washer page gives Detergent Low a single line: “Detergent Low will flash on the display when more detergent needs to be added to the bulk dispenser.” It adds nothing about cause.
Read the supporting manualNo reset is printed for Detergent Low on the front-load washer page. Writing down what the washer does around the code is the useful thing to do.
Read the supporting manualCL Code is a separate entry from Detergent Low on the front-load washer page, with its own wording.
Read the supporting manualThe front-load washer can still wash by hand-dosing detergent if the dispenser is the problem. Never open a panel on the front-load washer yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 14580 / PH 14580 (front-load washer)
Detergent Low comes from Maytag Product Help (PH 14580) for the front-load washer, read in November 2026; the Detergent Low entry names no models.
On the front-load washer page the line is “Detergent Low will flash on the display when more detergent needs to be added to the bulk dispenser.” No further cause is given.
There is no reset on that page. Note what happens and book us if Detergent Low persists.
Not by itself; the page stops at the line it prints.
Model and serial numbers plus a note of what happened when Detergent Low appeared.
Maytag codes, symptoms, parts and service
On a front-load washer, the entry for CL Code says “The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
F8E2 on a Maytag front-load washer is a dispenser system problem, and Product Help wants you to confirm the drawer or cartridge is not clogged with detergent. On top-load models F8E2 is the bulk dispenser and F3E5 the mini dispenser. dET means the cartridge is not detected.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.