Maytag washer F20 / Water and drain

Maytag washer
error code F20

Washer / display reference

Maytag's front-load washer page words F20 like this: “F20 indicates a water inlet problem-no water or insufficient water supply.” Try the five-minute power-off reset, and schedule a visit if the code returns.

Also printed as F20

Last reviewed

Washer / display reference
Meaning
Maytag's front-load washer page words F20 like this: “F20 indicates a water inlet problem-no water or insufficient water supply.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Who handles it
Reset, then book
Related codes
Source
F20 - Front Load Washer - Product Help | Maytag

What Maytag washer F20 means.

What it means

Maytag's front-load washer page words F20 like this: “F20 indicates a water inlet problem-no water or insufficient water supply.” Try the five-minute power-off reset, and schedule a visit if the code returns.

What you can safely check

Power and water off before any panel comes off; towels down for spills.

When to call a technician

F20 returns, or the front-load washer behaves oddly around the code.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 6 checks done
  1. Maytag washer F20: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Before you start

    Power and water off before any panel comes off; towels down for spills.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Read the display

    Record F20 character by character and note the product type: front-load washer.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Run the reset

    Power off for five full minutes, then on, and look for F20.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Watch afterward

    Run the washer briefly after the reset and see whether F20 comes back.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Appliance-specific check

    Check both water taps behind the front-load washer are fully open and the hoses are not kinked.

  6. Illustration. Follow your model’s instructions.
    Check 6

    Have this ready

    Keep the model number close and note when F20 appeared and what the front-load washer was doing.

Does F20 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does Maytag print beside F20 for a front-load washer?

The front-load washer entry for F20 reads “F20 indicates a water inlet problem-no water or insufficient water supply.” That is the whole explanation Maytag prints.

Read the supporting manual

Which first steps does Maytag give for F20?

Leave the washer off power for five full minutes, switch it back on, and check the display for F20.

Read the supporting manual

Is F20 the same as F0E1 on a front-load washer?

F0E1 is a neighbor of F20, not a synonym. The reset may overlap; the text does not.

Read the supporting manual

How careful should I be with the front-load washer while F20 is up?

A fill problem will not harm you, but do not leave the front-load washer filling unattended.

Read the supporting manual

The manual behind the message.

Manufacturer document

F20 - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-11-19; PH 14598 / PH 14598 (front-load washer)

Facts for F20 are from the front-load washer table (PH 14598) of Maytag Product Help, checked November 2026; no model list is printed.

Here to help

Good questions.
Clear answers.

Talk to our team
What does Maytag say F20 means?

As long as F20 stays on the front-load washer, the help page states “F20 indicates a water inlet problem-no water or insufficient water supply.” Nothing else is added.

How long must I cut power for F20?

Try it first; five minutes is the printed time. A returning F20 means schedule us.

Does the front-load washer page name a part for F20?

Not by itself; the page stops at the line it prints.

What should I have ready when I schedule for F20?

Model and serial numbers plus a note of what happened when F20 appeared.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.