Model-specific code library

Maytag washer Information codes

13 printed codes in this group: 1h, 2h, 3h....up to 12h, F0E3, F0E5, F0E7, F0E9, F7EC, Fd, Multiple Lights Flashing, OFb, oL and 3 more.

Top-load washer control panel with a dial knob and a lit display, a wicker basket of towels beside it
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Information codes

1h, 2h, 3h....up to 12h

On a front-load washer, the entry for 1h, 2h, 3h....up to 12h says “When the display shows a number up to 12, followed by an 'h,' the Delay Wash has been activated.” No reset is printed for it, so schedule a visit if it keeps appearing.

Information only
F0E3

The top-load page defines F0E3 as an overload: the load is too heavy and the overload recovery cycle is running. The front-load page prints only a reset. Reload loosely and balanced; if it persists, call for service.

Technician visit
F0E5

F0E5 is an unbalanced load on Maytag washers. The front-load page says a bulky item alone or a tightly packed load can lengthen the cycle and leave clothes dripping; the top-load page says cancel, drain, rearrange and restart.

Technician visit
F0E7

F0E7 means clothing was detected while the washer tried to run the Clean Washer cycle. Remove the load and restart the Clean Washer cycle. If the problem persists, call for service.

Technician visit
F0E9

F0E9 is an unbalanced load on a top-load washer. The washer first tries to self-correct by refilling and rotating gently; if it cannot, it shows the code. Cancel, drain, rearrange or reduce the load, then restart.

Technician visit
F7EC

On a front-load washer, F7EC asks first whether the washer is overloaded. Avoid tightly packing the load; clothing should move freely. Then cut power for 5 minutes and restart. If F7EC returns with a lighter load, schedule a visit.

Information only
Fd

Fd means Factory Default: Maytag’s top-load page says the washer was returned to factory default settings. The display shows Fd for 3 seconds, then the washer returns to Standby Mode. It is not an error that needs a repair.

Owner checks first
Multiple Lights Flashing

Multiple Lights Flashing on a Maytag top-load washer is explained as “Suppose the load is not evenly distributed in the basket when spinning begins.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.

Information only
OFb

For a Maytag top-load washer, Maytag's page for OFb says the washer could not even out an off-balance load by itself and needs you to spread the load around the washplate. Arrange a technician visit with us if it will not go away.

Owner checks first
oL

oL on a Maytag top-load washer is explained as “The load is too large if oL (overloaded) appears in the display.” Nothing else is printed, so schedule a visit if it repeats.

Information only
Sense and Wash Flashing

On a top-load washer, the entry for Sense and Wash Flashing says “Suppose the load is not evenly distributed in the basket when spinning begins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.

Information only
Spin Light Flashing

For a top-load washer showing Spin Light Flashing, Maytag prints “Suppose the load is not evenly distributed in the basket when spinning begins.” Try the five-minute power-off reset, and schedule a visit if the code returns.

Information only
uL

Maytag's top-load washer page words uL like this: “The washer could not remedy the off-balance load via automated methods and now needs manual intervention to...” No reset is printed for it, so schedule a visit if it keeps appearing.

Owner checks first

Let’s take care of it.

A full hamper waits for no one.
Book the repair.