What it means
On a top-load washer, the entry for Sense and Wash Flashing says “Suppose the load is not evenly distributed in the basket when spinning begins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer Sense and Wash Flashing / Information
On a top-load washer, the entry for Sense and Wash Flashing says “Suppose the load is not evenly distributed in the basket when spinning begins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as Sense and Wash Flashing
On a top-load washer, the entry for Sense and Wash Flashing says “Suppose the load is not evenly distributed in the basket when spinning begins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
Sense and Wash Flashing repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Match the label on your appliance to the top-load washer list before you rely on the wording for Sense and Wash Flashing.

No reset is printed here; note the behavior of the washer around Sense and Wash Flashing instead.

Note the model and the moment Sense and Wash Flashing showed up; both help us plan.

Check the machine stands level and does not rock on its feet.
Write down the model and serial numbers and the exact Sense and Wash Flashing wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Sense and Wash Flashing is covered by this wording on the top-load washer page: “Suppose the load is not evenly distributed in the basket when spinning begins.”
Read the supporting manualMaytag's page for Sense and Wash Flashing gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualPF is a separate entry from Sense and Wash Flashing on the top-load washer page, with its own wording.
Read the supporting manualRun a small load or a rinse to see if Sense and Wash Flashing clears. Never open a panel on the top-load washer yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-07-15; PH 14796 / PH 14796 (top-load washer)
Sense and Wash Flashing comes from Maytag Product Help (PH 14796) for the top-load washer, read in November 2026; the Sense and Wash Flashing entry names no models.
The help page states “Suppose the load is not evenly distributed in the basket when spinning begins.” Nothing else is added.
Nothing is printed for it, so record the display and schedule us if Sense and Wash Flashing continues.
Nothing about replacing parts is printed for Sense and Wash Flashing.
Model and serial numbers plus a note of what happened when Sense and Wash Flashing appeared.
Maytag codes, symptoms, parts and service
For a front-load washer showing PF, Maytag prints “The PF Error code indicates that the unit has experienced a power failure during operation.” No reset is printed for it, so schedule a visit if it keeps appearing.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.