What it means
For a top-load washer showing Add Garment Light On, Maytag prints “When Add Garment is lit, you may pause the cycle, open the lid, and add items.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer Add Garment Light On / Door and lid
For a top-load washer showing Add Garment Light On, Maytag prints “When Add Garment is lit, you may pause the cycle, open the lid, and add items.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as Add Garment Light On
For a top-load washer showing Add Garment Light On, Maytag prints “When Add Garment is lit, you may pause the cycle, open the lid, and add items.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Power and water off before any panel comes off; towels down for spills.
Add Garment Light On returns, or the top-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Match the label on your appliance to the top-load washer list before you rely on the wording for Add Garment Light On.

No reset is printed here; note the behavior of the washer around Add Garment Light On instead.

Write down the model and serial numbers and the exact Add Garment Light On wording before you call.

Do not force a locked door or lid; wait for the top-load washer to finish and release.
Keep the model number close and note when Add Garment Light On appeared and what the top-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The top-load washer entry for Add Garment Light On reads “When Add Garment is lit, you may pause the cycle, open the lid, and add items.” That is the whole explanation Maytag prints.
Read the supporting manualMaytag's page for Add Garment Light On gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualThe top-load washer list prints Sense and Wash Flashing next to Add Garment Light On, but with a different line. Look up the one on your display.
Read the supporting manualDo not bypass or tape a door switch on the top-load washer. Never open a panel on the top-load washer yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-04-22; PH 14716 / PH 14716 (top-load washer)
Facts for Add Garment Light On are from the top-load washer table (PH 14716) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag's wording is “When Add Garment is lit, you may pause the cycle, open the lid, and add items.” That is the whole entry.
Nothing is printed for it, so record the display and schedule us if Add Garment Light On continues.
No part is named for Add Garment Light On; the page gives only the wording above.
Tell us the model, the display wording and when Add Garment Light On first showed up.
Maytag codes, symptoms, parts and service
On a top-load washer, the entry for Sense and Wash Flashing says “Suppose the load is not evenly distributed in the basket when spinning begins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.