What it means
For a front-load washer showing PF, Maytag prints “The PF Error code indicates that the unit has experienced a power failure during operation.” No reset is printed for it, so schedule a visit if it keeps appearing.
Maytag washer PF / Power supply
For a front-load washer showing PF, Maytag prints “The PF Error code indicates that the unit has experienced a power failure during operation.” No reset is printed for it, so schedule a visit if it keeps appearing.
Also printed as PF
For a front-load washer showing PF, Maytag prints “The PF Error code indicates that the unit has experienced a power failure during operation.” No reset is printed for it, so schedule a visit if it keeps appearing.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
PF repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Record PF character by character and note the product type: front-load washer.

Maytag prints no reset for PF, so record what the washer does rather than guessing a fix.

Keep the model number close and note when PF appeared and what the front-load washer was doing.
Check the breaker for the front-load washer: a dryer needs both legs, and a tripped one can leave the drum dead.
Write down the model and serial numbers and the exact PF wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
PF is covered by this wording on the front-load washer page: “The PF Error code indicates that the unit has experienced a power failure during operation.”
Read the supporting manualNo reset is printed for PF on the front-load washer page. Writing down what the washer does around the code is the useful thing to do.
Read the supporting manualThe front-load washer list prints Sense and Wash Flashing next to PF, but with a different line. Look up the one on your display.
Read the supporting manualIf you see scorching at the plug or outlet, stop and call an electrician.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-04; PH 14586 / PH 14586 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-07-03; PH 13159 / PH 13159 (top-load washer)
Scope for PF: Maytag front-load washer, PH 14586, checked November 2026. Maytag lists no models on the PF page.
When PF is on the display of a front-load washer, Maytag's wording is “The PF Error code indicates that the unit has experienced a power failure during operation.” That is the whole entry.
No; Maytag gives PF no reset steps. If it repeats, schedule a visit.
Not by itself; the page stops at the line it prints.
Model and serial numbers plus a note of what happened when PF appeared.
Maytag codes, symptoms, parts and service
On a top-load washer, the entry for Sense and Wash Flashing says “Suppose the load is not evenly distributed in the basket when spinning begins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.