Maytag washer F8E1 commercial / Commercial-grade washer

Maytag washer
error code F8E1 commercial

Washer / display referenceF8E1 commercial

On Maytag's commercial-grade residential washer, F8 E1 means the washer is taking too long to fill, or it is filling and draining at the same time. Check the drain hose, confirm both hot and cold supplies are on, latch the lid and press Start for up to 3 seconds.

Also printed as F8E1

Last reviewed

Washer / display referenceF8E1 commercial
Meaning
On Maytag's commercial-grade residential washer, F8 E1 means the washer is taking too long to fill, or it is filling and draining at the same time. Check the drain hose, confirm both hot and cold supplies are on, latch the lid and press Start for up to 3 seconds.
Who handles it
Owner checks first, then a technician
Related codes
Source
Lid Lock is Flashing - Commercial Grade Washer - Product Help | Maytag

What Maytag washer F8E1 commercial means.

What it means

On Maytag's commercial-grade residential washer, F8 E1 means the washer is taking too long to fill, or it is filling and draining at the same time. Check the drain hose, confirm both hot and cold supplies are on, latch the lid and press Start for up to 3 seconds.

What you can safely check

The page says you may need to press and hold the Start button for up to 3 seconds to engage the cycle.

When to call a technician

F8E1 returns after the drain hose, both water supplies and the lid have been checked.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag washer F8E1 commercial: Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Press and hold Start

    The page says you may need to press and hold the Start button for up to 3 seconds to engage the cycle.

  2. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 2

    Latch the lid completely

    The lid must be completely closed and latched for the washer to operate.

  3. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 3

    Check the drain hose

    The page says a drain hose that reaches more than 4.5 inches (114 mm) into the standpipe can make the washer siphon, filling and draining at once. Attach it with a drain hose form, and do not tape over the drain opening.

  4. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 4

    Check both water supplies

    Connect both inlet hoses and turn on both the hot and the cold water. The sensors need water at both hoses.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Check the cycle selection

    The selector knob must sit on a cycle before you press Start. The page uses Normal as its example.

Does F8E1 commercial keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 2Control board
  3. 4Motor wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does F8E1 mean on a commercial-grade washer?

The washer is taking too long to fill, or it is filling and draining at once. Maytag prints F8 E1 and LF together for this.

Read the supporting manual

What causes the washer to fill and drain together?

A drain hose that extends more than 4.5 inches (114 mm) into the standpipe can let the washer siphon, so it never reaches the expected level.

Read the supporting manual

Why does the water supply matter?

Both inlet hoses must be connected, with hot and cold water on, because the sensors need water at both hoses.

Read the supporting manual

When should I book a visit?

Book if the code returns with the lid latched, a correct drain hose and both supplies on.

Read the supporting manual

The manual behind the message.

Manufacturer document

Lid Lock is Flashing - Commercial Grade Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-06-16; PH 11756 / PH 11756 (commercial-grade residential washer)

Manufacturer document

Lid Lock is Not On - Commercial Grade Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-06-17; PH 11757 / PH 11757 (commercial-grade residential washer)

Manufacturer document

Lid Lock is Solid Red - Commercial Grade Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-06-17; PH 14783 / PH 14783 (commercial-grade residential washer)

Facts come from three Maytag Product Help lid-lock pages for the commercial-grade residential washer (PH 11756, 11757, 14783), which carry identical text. Maytag has no error-code tree for this washer, so the codes are printed inside the lid-lock questions. These are commercial-grade units, not the household front-load or top-load washers.

Here to help

Good questions.
Clear answers.

Talk to our team
What does F8E1 mean on a commercial-grade washer?

The page says F8 E1 or LF (too long to fill) means the washer is taking too long to fill, or is filling and draining.

Is this the same as F8E1 on a household washer?

Not exactly. The household front-load page says the washer is not detecting the correct amount of incoming water. This page ties it to long fill, siphoning and a missing water supply.

Why does it need both hot and cold water?

The page says the washer has sensors that detect the water supply and need both hoses to have water. If it senses a hose is off, it sees a water pressure sensor problem.

What happens when it senses a missing supply?

The lid locks and the machine enters pump-out mode for 8 minutes.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.