Start from the symptom
Maytag washer front-load washer door seal problems.
Water left in the door seal (bellows) of a front-load Maytag washer is usually trapped by dirt, pet hair or a small item under the rubber. Pull the seal back and look all the way around, wipe it clean, and run the Clean Washer cycle each month. A dirty seal can also let water out at the front.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Look under the seal
Gently pull the seal back and inspect every area beneath it for stains, soil build-up or foreign objects.
- 2
Clean the bellows
Wipe stained areas with a damp cloth. Product Help gives a dilute bleach wash: 3/4 cup liquid chlorine bleach in 1 gallon of warm water, left for 5 minutes.
- 3
Protect your hands and air it out
Wear rubber gloves with bleach, wipe the seal dry afterward, and leave the door open so the drum can air dry.
- 4
Check the glass and drain holes
The door glass seals against the rubber, so deposits there can cause leaks. After each use, make sure the drainage holes in the seal are clear.
- 5
Do not overload
Clothing pushed outside the basket can catch in the seal and keep the door from sealing.
Systems a technician may investigate.
These parts tie in to the symptom. Noticing it does not prove that any single one has worn out.
If the display adds a code.
Read the related care guide.

Water still in the washer after the cycle: where it sits matters.
Where the water sits tells you what to do. A little in the dispenser area is normal, and more than half an inch after a thorough drawer cleaning is a service call. Water under the door seal usually means trapped lint, hair or small items, so clean the bellows monthly. Water in the tub with wet clothes points to an unbalanced load or a low spin, and Drain and Spin fixes that. [1][2][3][4]

A top-loader that will not agitate or spin: start with the load and the lid.
A Maytag top-load washer that stops agitating or spinning is most often reacting to the load or the setup, not to a broken part. Check balance, the cycle choice, the drain hose and standpipe, the level of the cabinet, a recent power cut, and anything resting on or under the lid. If dU or LdL stays on after that, book a technician. [1][2][3][4]
When observation becomes a service request.
Leave internal testing to a technician.
Water keeps leaking at the door after the seal and glass are clean.
The rubber is torn, or you cannot reach under it to clean.
The dispenser drawer, level and load size checks do not stop a front leak.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag front-load washer door seal problems advice. Read the manual for your own model.
- Water Remains in Door Seal (Bellows) - Front Load Washer - Product Help | Maytag
- Cleaning the Door Seal - Front Load Washer - Product Help | Maytag
- Leaking from Front - Front Load Washer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Is a little water in the door seal normal?
Some can sit there, but Product Help links it to build-up under the seal. It says to inspect and clean that area monthly and to run the Clean Washer cycle monthly.
How do I clean the door seal on a Maytag front-load washer?
Pull the seal back, wipe soil with a damp cloth, or use 3/4 cup liquid chlorine bleach in 1 gallon of warm water for 5 minutes. Wear gloves, wipe it dry, and leave the door open.
Why does my front-load washer leak from the door?
Product Help lists a dirty seal or glass, items stuck under the seal, a clogged or open dispenser drawer, non-HE detergent, an overloaded drum and a washer that is not level.
What does CL on the display mean?
CL is a reminder to run the Clean Washer cycle. It is a status message and not a repair order. It is also a good cue to check the door seal while the drum is empty.
Maytag codes, symptoms, parts and service
From the message to what you do next.
CL Code
On a front-load washer, the entry for CL Code says “The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer not draining
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Washer door seal (bellows)
The door seal, or bellows, on a Maytag front-load washer can trap small items, dirt and pet hair, and then hold water. Product Help says to inspect and clean it monthly and to run the Clean Washer cycle monthly. Its small drain holes can clog and slow draining.
Washer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.
