Start from the symptom
Maytag washer shaking and noisy.
Shaking, walking and thumping in a Maytag washer usually come from how it sits or how it is loaded: shipping bolts left in, a feet-off-the-floor wobble, a floor that flexes, a bulky single item, or hoses knocking the cabinet. Work through those before you book a technician. Some clunks are normal.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Rock it by hand
Grip the top and rock the washer toward you and away, then left and right; on a top-load, corner to corner. If it rocks, adjust the leveling feet, then tighten the jam nuts against the cabinet.
- 2
Shipping bolts and spacers
A front-load washer ships with four bolts and four plastic spacers on the rear. All must be out before use, or you may get noise, vibration or error codes.
- 3
Hoses against the cabinet
Drain or inlet hoses with room to swing will knock the back panel. Secure them with the beaded strap, where supplied, or a wire tie. Move brooms and racks that lean on the washer.
- 4
Balance the load
Do not wash a single bulky item alone. Add towels as counterweights. On a top-load, place clothes in loose heaps around the agitator and keep the load below the top row of basket holes.
- 5
Know the normal sounds
A clunk as a top-load shifts between agitation and spin is normal. So is a brief thump at slow spin on a front-load, and fluid sloshing in the balance ring after the washer is moved.
Systems a technician may investigate.
These parts tie in to the symptom. Noticing it does not prove that any single one has worn out.
If the display adds a code.
Information
For a Maytag top-load washer, Maytag's page for OFb says the washer could not even out an off-balance load by itself and needs you to spread the load around the washplate. Arrange a technician visit with us if it will not go away.
Information
Maytag's top-load washer page words uL like this: “The washer could not remedy the off-balance load via automated methods and now needs manual intervention to...” No reset is printed for it, so schedule a visit if it keeps appearing.
Information
oL on a Maytag top-load washer is explained as “The load is too large if oL (overloaded) appears in the display.” Nothing else is printed, so schedule a visit if it repeats.
Information
The top-load page defines F0E3 as an overload: the load is too heavy and the overload recovery cycle is running. The front-load page prints only a reset. Reload loosely and balanced; if it persists, call for service.
Information
F0E5 is an unbalanced load on Maytag washers. The front-load page says a bulky item alone or a tightly packed load can lengthen the cycle and leave clothes dripping; the top-load page says cancel, drain, rearrange and restart.
Read the related care guide.

Water still in the washer after the cycle: where it sits matters.
Where the water sits tells you what to do. A little in the dispenser area is normal, and more than half an inch after a thorough drawer cleaning is a service call. Water under the door seal usually means trapped lint, hair or small items, so clean the bellows monthly. Water in the tub with wet clothes points to an unbalanced load or a low spin, and Drain and Spin fixes that. [1][2][3][4]

A top-loader that will not agitate or spin: start with the load and the lid.
A Maytag top-load washer that stops agitating or spinning is most often reacting to the load or the setup, not to a broken part. Check balance, the cycle choice, the drain hose and standpipe, the level of the cabinet, a recent power cut, and anything resting on or under the lid. If dU or LdL stays on after that, book a technician. [1][2][3][4]
When observation becomes a service request.
Leave internal testing to a technician.
The washer still walks or bangs after leveling, hose securing and a balanced load.
The floor flexes or sags under the washer, or it sits on a raised wooden platform.
The washer stops spinning with an OFb, uL or F0E5 message and will not recover.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag washer shaking and noisy advice. Read the manual for your own model.
- Vibration or Out of Balance loads - Product Help | Maytag
- Knocking or Thumping - Noise - Product Help | Maytag
- Clunk or Clunking - Noise - Product Help | Maytag
- Vibration, Walking or Off Balance - Front Load Washer - Product Help | Maytag
- Banging Noise - Front Load Washer - Product Help | Maytag
- Thumping Noise - Front Load Washer - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Why does my Maytag washer shake during the spin?
The usual reasons in Product Help are an unlevel washer, feet not touching the floor, shipping bolts still fitted, and an unbalanced or overloaded load. A single bulky item should be washed with towels.
Is the clunk in my top-load washer normal?
Yes. Product Help says there is a clunk as the drive system moves between agitation and spin, and that these sounds are part of normal operation.
Why does the cycle run longer when the load is off balance?
A top-load washer senses an out-of-balance load, then adds water and agitation to correct it. Longer cycle time can mean it is doing that, and Maytag says to let it continue.
Does a washer need to sit on a solid floor?
Yes. Product Help says to check the floor for flexing or sagging and not to install a washer on a raised wooden platform, since it will vibrate.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Maytag washer OFb error code
For a Maytag top-load washer, Maytag's page for OFb says the washer could not even out an off-balance load by itself and needs you to spread the load around the washplate. Arrange a technician visit with us if it will not go away.
Maytag washer not draining
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Top-load washer balance ring
The balance ring on a Maytag top-load washer is a fluid-filled ring at the top of the tub. As a load shifts, the fluid moves to the opposite side to steady the basket and allow faster spins. Product Help says it is the usual cause of water heard but not seen, and it may slosh when you move the washer.
Washer repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.
