On this page
- Washers on the F5 E1, F7 E1 and Err pages: disconnect power for 5 minutes. 123
- Dryers: breaker off for 5 minutes on F1 E1, F4 E4 and L2, and for one minute on F3 E3 and F4 E1. 4567
- Dishwashers: 30 seconds without power, by plug or breaker. 89
- Ranges and refrigerators: one minute without power. 1011
- A code still showing after a full wait calls for a technician. 8
Why does the reset wait differ between machines?#
Maytag prints a different wait on each code page: 5 minutes for washers, 30 seconds for dishwashers, and either 1 or 5 minutes for dryers. Ovens and refrigerators ask for one minute. The pages do not explain the gaps, so follow the number for your machine. 14810
A Maytag is built for busy households, and the control board inside gets the same treatment on every model: electricity is taken away, the board starts again, and the machine reports whether the condition is still there. Where the pages differ is the length of the pause and the way you cut the supply. The table collects what each page prints.
| Machine | How to cut the supply | Wait | What to do after |
|---|---|---|---|
| Washer, either layout | Unplug the unit 12 | 5 minutes | Plug in and run a cycle 1 |
| Dryer, F1 E1, F4 E4, L2 | Breaker off 47 | 5 minutes | Start a timed dry, watch 1 to 5 minutes 47 |
| Dryer, F3 E3, F4 E1 | Breaker off 56 | 1 minute | Start a timed dry, watch 1 minute 56 |
| Dishwasher | Unplug, or breaker off if hard wired 8 | 30 seconds | Run a cycle 8 |
| Range | Breaker off 10 | 1 minute | Start a bake cycle 10 |
| French-door refrigerator | Breaker off or unplug 11 | 1 minute | Confirm cooling is on 11 |

How long does a washer stay unplugged?#
Five minutes. The pages for F5 E1, F7 E1 and Err all say the control needs to be disconnected from its power source for 5 minutes, then plugged back in. Maytag's wording is that resetting the control can sometimes solve the issue. 123
Two of those pages ask you to check something before the reset. F5 E1 is the door switch: the door has to be fully closed, with nothing such as clothing or shipping material in the way of the switch. 1 F7 E1 on a front-load washer is a motor speed sensing message, and its page asks whether all four shipping bolts and the plastic spacers were taken off the back of the washer, because leaving them can bring noise, vibration or error codes. 2
The Err message on a front-load washer is a different case. The page says it appears when you try to change a cycle that is already running or try to start a cycle with the door open, so the first step is to close the door and set the cycle again, then use the 5 minute reset if it stays. 3
Our table of washer codes lists F5 E1, F7 E1 and Err with the product type each page covers.
- 1
- 2
- 3
- 4
What does a dryer need after a code?#
The breaker, not the plug, is the usual route: switch it off for 5 minutes (F1 E1, F4 E4, L2) or 1 minute (F3 E3, F4 E1), switch it back on, start a timed dry cycle and watch the display. The monitoring time is 5 minutes, or one minute on the short pages. 4567
F1 E1 is the plainest page. It lists only the reset: breaker off 5 minutes, breaker on, a timed dry cycle, then one minute of watching to be sure the code does not reappear. 4 F3 E3 (inlet thermistor) and F4 E1 (heater system) use a one-minute breaker pause and one minute of monitoring. 56
F4 E4 and L2 are the two that read "low or no line voltage." Before the reset, the pages ask you to check the household supply: an electric dryer is on a separate 30-amp circuit with two breakers, one for the motor and one for the heater, and both should be on. They also state that an electric dryer needs 240 volts and tightly seated terminal screws, and they say to unplug the dryer before touching the terminal screws. 7 On L2 the dryer keeps running while the code shows, and any pad you touch clears it. 7
Our pages for F1 E1, F4 E4 and L2 show the full text. If the dryer will not start at all, the dryer will not start page is the better place to begin.
What is the reset for a dishwasher?#
Cut its power for 30 seconds. A plug-in model comes out of the wall socket and goes back in afterward; a hard-wired one has its breaker at the home panel switched off, then on. Maytag says to schedule service if the code returns. 89
The same 30-second instruction appears on the F1E1 page and in Maytag's dishwasher code-reading article, which also explains how a flashing-light model counts out a code: the first run of flashes is the F number, a pause of one to two seconds follows, the second run is the E number, and a longer pause of about five seconds comes before it repeats. 89
Not every dishwasher message wants a reset. For H2O, the page asks you to confirm the water supply is on and that the supply hose has no kinks, then press Start so the dishwasher can try to fill and resume. 9 Our dishwasher H2O entry has that text, and the dishwasher F1E1 entry has the reset.
What about an oven or a refrigerator?#
Both are one minute. On a range, the Press Cancel to Reset message first asks you to press Cancel; if Call Service then appears, cut the breaker for a minute, restore it, run a bake cycle and observe the display for 60 seconds. A French-door refrigerator showing a flashing F gets a one-minute pause too. 1011
For the refrigerator the sequence adds a step: after power returns, make sure the cooling function is on, then watch for one minute. If the problem stays, Maytag's page says to schedule service. 11 Our entries for Press Cancel to Reset and the flashing F keep the product scope.
What belongs in my notes before I restart the machine?#
Write down the code, the cycle, and how long the machine ran before it appeared. Tell us whether you unplugged or used the breaker, and how long you waited. Those details let a technician tell a one-off reading from a pattern.
- What exactly did the display show, and was it flashing?
- Which cycle was running, and was the load unusual?
- How long was the machine off, and how was the supply cut?
- Did the code return at once, or after a few cycles?
- For a dryer, were both breakers on and the vent clear?
Our work on Maytag washers, dryers and dishwashers is described on the washer, dryer and dishwasher pages.
Sources#
- F5E1 - Error Code - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2025-05-27; PH 13442 · article text, Possible Solutions
- F7 E1 - Front Load Washer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2025-05-27; PH 14617 · article text, Possible Solutions
- Err - Error Code - Front Load Washer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2025-06-04; PH 14582 · article text, Possible Solutions
- F1 E1 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2025-04-11; PH 12789 · article text, Possible Solutions
- F3 E3 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-08-19; PH 12807 · article text, Possible Solutions
- F4 E1 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-08-19; PH 12810 · article text, Possible Solutions
- F4 E4 - Error Code - Dryer - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2025-05-27; PH 12812 · article text, Possible Solutions
- F1E1 - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-06-15; PH 12623 · article text, Possible Solutions
- Dishwasher Error Codes - Reading - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-08-31; PH 15083 · article text, Possible Solutions
- Press Cancel to Reset - Range - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2024-11-07; PH 13888 · article text, Possible Solutions
- Flashing "F" - Error Code - Refrigerator - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2024-04-25; PH 9714 · article text, Possible Solutions



