Before work starts
Your technician checks the washer, dryer or other appliance, then gives you the cost. The repair goes ahead only with your okay.
Independent appliance repair
We repair Maytag dishwashers: leaks at the door or underneath, water that will not drain, an F-and-E code on the display, or a flashing and beeping pattern. Book a technician and we trace it on site, with the price agreed first.

F8E4 on a Maytag dishwasher: Maytag's reading table gives water in the drip tray as the cause, while the F8E4 pages print install checks and safety steps. Close the water line, leave the door latched and schedule a visit with us.
For a Maytag dishwasher, Maytag's page for F8E5 says the potential cause it lists is: the fill valve has stuck in the open position. Close the water line to the dishwasher, keep the door shut, then schedule a visit with us.
For a Maytag dishwasher, Maytag's page for F9E1 says the potential cause it lists is: the drain takes too long. To reset it, leave the circuit breaker off for 30 seconds before switching it back on. Arrange a technician visit with us if the display shows it again after the reset.
Maytag's page on F3E2 for the dishwasher says the potential cause it lists is: the trouble is in the thermistor or the OWI sensor. To reset it, leave the circuit breaker off for 30 seconds before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
We pick the part after we read the model label and test the unit. Nothing is ordered ahead of time, and the quote is yours to approve before any work begins.

On a Maytag dishwasher, FAE4 lists a diverter valve error and FAE5 lists a diverter leak. For FAE5, Product Help says to check for leaks under the dishwasher, make sure water connections are secure, press Cancel twice and start a new cycle. FAE4 gets a 30-second power reset.

F8E5 on a Maytag dishwasher lists a fill valve stuck open, and the page leads with stopping the water. Product Help says to shut the water supply when you can reach it, press Cancel one time to quiet the tone, and close the door. Leave power on unless the water cannot be stopped.

F8E4 on a Maytag dishwasher means water was detected in the drip tray. Product Help checks the water connections, whether the float switch is reconnected, and whether the tray holds water that needs to be emptied. F6E4 names the water float switch and asks you to level the dishwasher.

F3E2 on a Maytag dishwasher lists a thermistor or OWI sensor as the potential cause. Product Help offers one home step: cut power to the dishwasher for 30 seconds, by unplugging it or by switching its breaker off. A returning code means scheduling service.

F9E1 on a Maytag dishwasher is a long drain and F9E2 is a drain motor error. Product Help lists the checks: clean the filter under running water, look for a kinked or clogged drain hose, and confirm the garbage disposer knockout plug is out on a new installation.
Three steps from request to repair.
You stay in the loop the whole way.

Pick washer or dryer and tell us what it does: no spin, no heat, loud thumping. Book online any time.

The technician tests the machine and quotes the work. You approve the price before a tool comes out.

After the repair the technician runs the machine with you and explains what was changed.
Maytag prints each F-E pair and each pause pattern, such as 8 pause 5 pause for F8E5.
Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds.
Underneath: water supply connections and the drain line. At the door: dish soap, pre-washed dishes, items under the seal, and levelness.
Clean the filter, straighten the hose, and on a new install confirm the disposer knockout plug is out.
Shut the supply valve when it is within reach, tap Cancel one time, and leave the door shut. Kill power only when the water cannot be stopped.
F8E5 appears, or water reaches the floor.
F8E4, F9E1 or F3E2 returns after the checks.
Suds come out of the dishwasher.
It will not fill or will not start after a power cycle.
Arrange a diagnosticYour technician checks the washer, dryer or other appliance, then gives you the cost. The repair goes ahead only with your okay.
Maytag deals with repairs its warranty covers. Every repair we complete is backed by our workmanship warranty.
Each pause pattern maps to an F-E code on a Product Help page, for example 8 pause 5 pause is F8E5. Count the beeps and tell us.
Dish soap, pre-washed or soaked dishes, items between the door seal and the tub, and whether the dishwasher is level.
Cut power for 30 seconds by unplugging it or switching the breaker off, then restore power.
We can diagnose it. Product Help starts with water connections and the float switch on a new install.
For a unit still covered by the manufacturer's warranty, the maker takes that repair. After coverage ends, schedule a technician with us and approve the quote first.
Maytag codes, symptoms, parts and service
F8E4 on a Maytag dishwasher: Maytag's reading table gives water in the drip tray as the cause, while the F8E4 pages print install checks and safety steps. Close the water line, leave the door latched and schedule a visit with us.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
On a Maytag dishwasher, FAE4 lists a diverter valve error and FAE5 lists a diverter leak. For FAE5, Product Help says to check for leaks under the dishwasher, make sure water connections are secure, press Cancel twice and start a new cycle. FAE4 gets a 30-second power reset.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.