What it means
F8E4 on a Maytag dishwasher: Maytag's reading table gives water in the drip tray as the cause, while the F8E4 pages print install checks and safety steps. Close the water line, leave the door latched and schedule a visit with us.
Maytag dishwasher F8E4 / Water and drain
F8E4 on a Maytag dishwasher: Maytag's reading table gives water in the drip tray as the cause, while the F8E4 pages print install checks and safety steps. Close the water line, leave the door latched and schedule a visit with us.
Also printed as F8E4
F8E4 on a Maytag dishwasher: Maytag's reading table gives water in the drip tray as the cause, while the F8E4 pages print install checks and safety steps. Close the water line, leave the door latched and schedule a visit with us.
Water is involved: close the water line to the dishwasher first and keep the door shut.
Water has collected around the dishwasher.
Your Maytag to-do list, saved here on this device

Copy F8E4 down as the display shows it, capitals and dashes included, and note the product type: dishwasher.

Maytag's pages ask you to close the water line to the dishwasher and keep the door shut.

The F8E4 pages ask for one press of Cancel and tell you not to switch the power off.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F8E4 on a Maytag dishwasher means water was detected in the drip tray.
Read the definitionThe reading table gives water in the drip tray as the cause; the F8E4 pages themselves give install checks and safety steps.
Read the supporting manualIn order: close the water line, press Cancel one time, leave the door latched and keep the power on. After a new install the page lists setup checks.
Read the supporting manualNo reset interval is printed for it.
Read the supporting manualSchedule one with us if F8E4 reappears once the water supply is back on. Have the exact display wording and the model number ready.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-08-31; PH 15083 / PH 15083 (dishwasher, reading page table)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12611 / PH 12611 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12632 / PH 12632 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-17; PH 12699 / PH 12699 (dishwasher)
Scope: Maytag dishwasher. Source pages: Maytag Product Help, PH 15083, 12611, 12632, 12699, checked November 2026.
The reading table gives water in the drip tray as the cause; the F8E4 pages themselves give install checks and safety steps.
No reset interval is printed on the page. Note when the message appears, and schedule a visit if it will not clear.
No part is named on the page. It describes the condition and what you can do about it.
Schedule one if F8E4 reappears once the water supply is back on. Until then, the steps above are all the page asks of you.
Maytag codes, symptoms, parts and service
For a Maytag dishwasher, Maytag's page for F8E5 says the potential cause it lists is: the fill valve has stuck in the open position. Close the water line to the dishwasher, keep the door shut, then schedule a visit with us.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
F8E4 on a Maytag dishwasher means water was detected in the drip tray. Product Help checks the water connections, whether the float switch is reconnected, and whether the tray holds water that needs to be emptied. F6E4 names the water float switch and asks you to level the dishwasher.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.