Start from the symptom
Maytag dishwasher burning smell.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Let it cool
Wait at least 30 minutes after a cycle before reaching near the heating element.
- 2
Clear the element area
Remove plastic pieces or food particles from around the heating element. A wooden spoon works, and Product Help advises a non-metal tool.
- 3
Run a rinse or cleaning cycle
A rinse, or a cycle with affresh cleaner, helps remove the odor. After a few cycles any leftover plastic burns off.
- 4
Check what you washed
Only put dishwasher-safe plastic in, and only on the upper rack.
- 5
New dishwasher?
Some models have a black rubber sound-deadening coat on the outside of the tub that smells of hot tar or petroleum. This is normal for a new dishwasher.
Systems a technician may investigate.
We pick the part after we read the model label and test the unit. Nothing is ordered ahead of time, and the quote is yours to approve before any work begins.

Dishwasher diverter (FAE4, FAE5)
On a Maytag dishwasher, FAE4 lists a diverter valve error and FAE5 lists a diverter leak. For FAE5, Product Help says to check for leaks under the dishwasher, make sure water connections are secure, press Cancel twice and start a new cycle. FAE4 gets a 30-second power reset.

Dishwasher fill valve (F8E5, F8E2, H2O)
F8E5 on a Maytag dishwasher lists a fill valve stuck open, and the page leads with stopping the water. Product Help says to shut the water supply when you can reach it, press Cancel one time to quiet the tone, and close the door. Leave power on unless the water cannot be stopped.

Dishwasher float switch and drip tray (F8E4, F6E4)
F8E4 on a Maytag dishwasher means water was detected in the drip tray. Product Help checks the water connections, whether the float switch is reconnected, and whether the tray holds water that needs to be emptied. F6E4 names the water float switch and asks you to level the dishwasher.

Dishwasher thermistor and OWI sensor (F3E2)
F3E2 on a Maytag dishwasher lists a thermistor or OWI sensor as the potential cause. Product Help offers one home step: cut power to the dishwasher for 30 seconds, by unplugging it or by switching its breaker off. A returning code means scheduling service.

Dishwasher drain system (F9E1, F9E2)
F9E1 on a Maytag dishwasher is a long drain and F9E2 is a drain motor error. Product Help lists the checks: clean the filter under running water, look for a kinked or clogged drain hose, and confirm the garbage disposer knockout plug is out on a new installation.
If the display adds a code.
This topic has no code of its own.
We have linked no other researched dishwasher code to this topic. Compare the exact message with your model’s manual and do not borrow another code from the library.
See the research statusRead the related care guide.

Water on the kitchen floor near the dishwasher: door, base or tray?
Water at a Maytag dishwasher usually comes from steam at the door vent, suds, a pre-washed or soaked load, an item caught in the door seal, an unlevel or out-of-square tub, or a loose supply or drain connection. Check those first. Water in the drip tray, which goes with an F8E4 code, must be emptied, and the supply shut off if the code appears. [1][2][3]

A dishwasher light is flashing. Is it a code?
A flashing Sanitize light, a Control light that blinks three times, and every cycle and option light flashing are not F-E codes on a Maytag dishwasher. They point to water that was too cool, a locked panel, and a door opened mid-cycle. Check those, close the door, and power-cycle for 30 seconds if the pattern stays. [1][2][3]
When observation becomes a service request.
Leave internal testing to a technician.
The smell stays after the debris is cleared and a cleaning cycle has run.
The smell is strong and comes with smoke or a hot, melted look at the door.
The dishwasher is older than a few weeks, so the new-unit coating does not apply.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag dishwasher burning smell advice. Read the manual for your own model.
- Melted Plastic or Charred Food Odor - Dishwasher - Product Help | Maytag
- Hot tar or Petroleum Like Odor - Dishwasher - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Why does my Maytag dishwasher smell like burnt plastic?
Plastic or food particles may have dropped around the heating element during a cycle. Product Help says to cool the tub first, clear the debris, and run a rinse or cleaning cycle.
How long should I wait before checking the element?
At least 30 minutes after the dishwasher has fully cooled. Scrape debris away with a non-metal item such as a wooden spoon, not a knife or a metal tool.
Is a hot tar smell on a new dishwasher a problem?
No. Maytag says some models carry sound-deadening material that smells of hot tar or petroleum, and that it should fade within 4 to 6 weeks.
Where do plastic items go in a dishwasher?
Only dishwasher-safe plastic, and only on the upper rack. Items that are not rated for it can melt and leave a smell that takes a few cycles to burn off.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Maytag dishwasher burning smell
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
Dishwasher repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.