Error codes explained

Maytag dishwasher lights that are not codes

A flashing Sanitize light, a Control light that blinks three times, and every cycle and option light flashing are not F-E codes on a Maytag dishwasher. They point to water that was too cool, a locked panel, and a door opened mid-cycle. Check those, close the door, and power-cycle for 30 seconds if the pattern stays. [1][2][3]

A hand rests on the open door of a stainless dishwasher whose control strip shows five small round lights, one lit.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Sanitize light flashing: the sanitizing temperature was not met, so the dishes were not sanitized. 1
  • Control light flashing three times: a button was pressed while the controls were locked. 2
  • All cycle and option lights flashing: the door was opened mid-cycle and the cycle is suspended. 3
  • Front status light: blue washing, red drying, white complete, blinking paused. 4
  • A flashing-light code counts the F flashes, pauses, then counts the E flashes. 7

Which dishwasher lights are signals and not codes?#

Four light behaviors on a Maytag dishwasher have plain explanations: a flashing Sanitize light, a Control light that blinks three times, every cycle and option light flashing, and the colored status light on the front. None of them is an F-E code. Each has its own check below. 1234

A dishwasher in a busy home gets opened mid-cycle, loaded in a hurry and sometimes locked by a small hand. The lights record all of that, and Maytag's pages treat these patterns as things to check before any repair.

What you seeWhat Maytag's page saysFirst move
Sanitize light flashingSanitizing temperature was not met 1Check the hot water at the sink
Control light, three flashesButton pressed while controls locked 2Hold Control Lock about 3 seconds
All cycle and option lights flashingDoor opened mid-cycle, cycle suspended 3Latch the door firmly
Front light blue, red, white or blinkingWashing, drying, complete, paused 4Read the stage, no action needed
Counted flashes with pausesA real F-E code 7Count and record it
A single small blue light glows on the top front edge of a stainless dishwasher door in a kitchen.
The front status light shows the stage of the cycle, which is a different thing from a code. 4

What does a flashing Sanitize light mean?#

The Sani light flashes when the dishwasher detects that the sanitizing temperature was not reached. Maytag's page calls that a clear sign the dishes were not sanitized. Run the hot tap for about 30 seconds and check it against the 120 degrees F minimum in the Owner's Manual. 1

The page asks two other questions. Was the door opened during the cycle, so heat escaped, and was power interrupted? Either can leave the sanitize cycle short of its target. If both answers are no and the water is hot, the page suggests cycling power to reset the control. 1

  1. 1

    Run the hot water#

    Open the sink's hot tap for about 30 seconds and feel the water. The sanitize minimum in the manual is 120 degrees F (49 degrees C). 1

    A hand held under a kitchen faucet with water running and a little steam rising over a stainless sink.
  2. 2

    Think back over the cycle#

    Was the door opened partway through, or did the power drop? Either one can mean the temperature was missed. 1

  3. 3

    Cycle power for 30 seconds#

    Cut power for 30 seconds, by pulling the plug or by the breaker, then restore it. 1

  4. 4

    Run the sanitize cycle again#

    Leave the door shut for the whole cycle and watch whether the light still flashes. 1

A red glow once the cycle is over is the other side of this: Maytag's Glowing Red page says the Sani Rinse indicator lights at the end when the option finished, and that an indicator that does not light is probably a sign the cycle was interrupted. 5 Our entries for Sanitize Light Flashing and Glowing Red hold the page text.

Why does the Control light flash three times?#

The control lock is probably on. Maytag says the light flashes three times when any button is pressed while the controls are locked. To unlock, keep Control Lock pressed for about three seconds; the exact time depends on the model. 2

When that fails, the panel may be in Sleep Mode. The page says to press Start/Resume or Cancel, or open and close the door, and points you to your Control Guide or Owner's Manual for model specifics. 2 When neither works, the same page offers the 30 second power cycle. 2 See the Control Light Flashing entry.

Why are all the cycle and option lights flashing?#

You opened the door during a cycle. Maytag says every selected cycle and option light flashes to show the cycle is suspended. Close the door until it latches, and after a slight delay the cycle resumes at the point it stopped. 3

This is the one that worries people most, because a whole row of lights blinking looks serious. It is closer to a pause button. The page says the lights stop when the door is shut properly, and only offers the power cycle if they do not. 3 The All Cycle And Option Lights entry carries the text.

What do the front status lights mean?#

On models with a status light on the front, blue means washing is in progress, red means drying is in progress, white means the cycle is complete, and blinking means the cycle has paused. 4

Maytag has a second page for a dishwasher whose front status light is not lit at all. It repeats the color meanings and asks for a power cycle of 30 seconds, by pulling the plug or using the breaker, then restoring power. 6 Because the Glowing Red page talks about the Sani Rinse indicator and the front-light page says red means drying, match the light to where it sits on your door before you read the meaning. 45

Does a missed Sanitize light matter?#

Only if you needed sanitized dishes. Maytag's Glowing Red page says the Sani Rinse indicator glows once a cycle finishes with that option complete, and that only sanitizing cycles were designed to meet the NSF/ANSI 184 standard. Certified residential dishwashers are not meant for licensed food businesses. 5

So the flashing light tells you about that one option, not about the whole dishwasher. If everyday cycles clean well, and only the sanitize result is missing, check the hot water and the door as above before you look further. 15

How do I tell these lights from a real code?#

A real code on a flashing-light model is a counted sequence: fast flashes for the F number, a pause of one to two seconds, fast flashes for the E number, then about five seconds of quiet before it repeats. Digital models show the code as F#E#. 7

Seven flashes, a pause, then one flash, for example, reads F7 E1. Maytag also says that a flashing Clean light usually points to a code being communicated. 7 If your lights follow that pattern, record the numbers and use the dishwasher code table. For H2O, the page asks you to make sure the water supply is on and the hose has no kinks, then press Start. 8

What helps the visit go faster?#

Say which light it was, how many times it flashed, and what you did. A clip filmed on your phone, door open and then shut, shows more than a description.

  • Which light flashed, and was it steady, blinking or counted?
  • What was the temperature of the hot water at the sink?
  • Was the door opened or the power interrupted during the cycle?
  • Did the 30 second power cycle change anything?
  • Does the dishwasher have a front status light, and what color is it?

Dishwasher repairs we carry out on Maytag units are described on our dishwasher page.

Sources#

  1. Sanitize Light Flashing - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2025-05-27; PH 12616 · article text, Possible Solutions
  2. Control Light Flashing - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2025-05-27; PH 14545 · article text, Possible Solutions
  3. All Cycle And Option Lights flashing - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-06-15; PH 12614 · article text, Possible Solutions
  4. Front Status Lights - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2024-04-25; PH 12639 · article text, Possible Solutions
  5. Glowing Red - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-06-08; PH 15074 · article text, Possible Solutions
  6. Front Status Lights Not Illuminated - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-06-08; PH 15075 · article text, Possible Solutions
  7. Dishwasher Error Codes - Reading - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-08-31; PH 15083 · article text, Possible Solutions
  8. H2O - Dishwasher - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · dateModified 2026-06-15; PH 12638 · article text, Possible Solutions

Here to help

Good questions.
Clear answers.

Talk to our team
Does a flashing Sanitize light mean the dishwasher is broken?

Not on Maytag's page. The Sani light flashes when the sanitizing temperature was not reached, which means the dishes were not sanitized. Check the hot water at the sink and whether the door was opened mid-cycle. [1]

Why did the Control light blink three times when I pressed a button?

The controls are probably locked. Maytag says the light flashes three times if a button is pressed during lock. Keep the Control Lock button pressed for roughly three seconds to unlock it, or wake the panel from Sleep Mode. [2]

All the cycle lights are flashing after I opened the door. Is that a code?

No. Maytag says opening the door during a cycle suspends it and flashes every selected cycle and option light. Shut the door until it latches and the cycle picks up again after a short delay. [3]

What does a white front light mean?

On models with a front status light, white means the cycle is complete. Blue means washing is in progress, red means drying is in progress, and blinking means the cycle has paused. [4]

How do I tell these lights from a real error code?

A real code is a two-part count: flashes for F, a pause, then flashes for E, then a longer pause before it repeats. A steady or one-off pattern tied to a button, the door or the lock is not that. [7]

Let’s take care of it.

A full hamper waits for no one.
Book the repair.