What it means
Maytag Product Help prints H2O as “Not Detecting Water”: make sure the water supply is on, check for kinks in the supply hose, then press Start and the dishwasher will try to fill and resume. The page also lists it as F8E1 or H20.
Maytag dishwasher H2O / Water and drain
Maytag Product Help prints H2O as “Not Detecting Water”: make sure the water supply is on, check for kinks in the supply hose, then press Start and the dishwasher will try to fill and resume. The page also lists it as F8E1 or H20.
Also printed as H2O
Maytag Product Help prints H2O as “Not Detecting Water”: make sure the water supply is on, check for kinks in the supply hose, then press Start and the dishwasher will try to fill and resume. The page also lists it as F8E1 or H20.
Switch off power and the water supply before opening anything, and wipe up spills so nobody slips.
H2O returns with the water on and the hose clear.
Your Maytag to-do list, saved here on this device

Make sure the supply valve to the dishwasher is turned on.

The page says to make sure there are no kinks in the water supply hose.

Once the water supply is corrected, press Start. The dishwasher attempts to fill and resume the cycle.

Eight flashes, a pause, one flash. The page for that pattern is titled “F8E1 or H20 Error Code.” [1]

The pattern page spells it H20 with a zero, while the error code page spells H2O with a letter O. Write down what you see.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F8E5 on a Maytag dishwasher lists a fill valve stuck open, and the page leads with stopping the water.
Read the definitionThe cause line is “Not Detecting Water.” The page has no power cycle. It tells you to ensure the water is on, check the supply hose for kinks, then press Start.
Read the supporting manualThe pattern page is titled F8E1 or H20, and the Reading page lists the code as H20 in its table. The error code page spells it H2O.
Read the supporting manualF8E5 is a fill valve stuck open: shut the water off. H2O is the opposite, water is not detected, so the first job is to turn it on.
Read the supporting manualThe “will not fill” row of the retailer-copy manual says to be sure the water is turned on, check that the float is free of obstructions, and check for suds.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12610 / PH 12610 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12638 / PH 12638 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12633 / PH 12633 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-08-31; PH 15083 / PH 15083 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Sources: Product Help PH 12610 and PH 12638, with the F8E5 and Reading pages.
Yes, the pages use both spellings and F8E1.
Not on this page. The steps are water on, hose straight, press Start.
If the water is on and the hose is clear, the code returning means a visit.
The page says it will attempt to fill and resume the cycle once you press Start.
Maytag codes, symptoms, parts and service
Maytag prints F6E1 as “Potential Cause: User Interface Error, Main Control” on two pages, the six-flash pattern page and the error code page. Cycle power for 30 seconds; if the code remains, call for service.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
F8E5 on a Maytag dishwasher lists a fill valve stuck open, and the page leads with stopping the water. Product Help says to shut the water supply when you can reach it, press Cancel one time to quiet the tone, and close the door. Leave power on unless the water cannot be stopped.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.