What it means
Maytag prints F6E1 as “Potential Cause: User Interface Error, Main Control” on two pages, the six-flash pattern page and the error code page. Cycle power for 30 seconds; if the code remains, call for service.
Maytag dishwasher F6E1 / User interface
Maytag prints F6E1 as “Potential Cause: User Interface Error, Main Control” on two pages, the six-flash pattern page and the error code page. Cycle power for 30 seconds; if the code remains, call for service.
Also printed as F6E1
Maytag prints F6E1 as “Potential Cause: User Interface Error, Main Control” on two pages, the six-flash pattern page and the error code page. Cycle power for 30 seconds; if the code remains, call for service.
Close the water valve and the breaker before any panel comes off.
F6E1 remains after the 30-second power cycle.
Your Maytag to-do list, saved here on this device

Unplug the dishwasher for 30 seconds, or turn its breaker off for 30 seconds if it is hard wired, then restore power.

Six rapid flashes, a pause of about 1 to 2 seconds, one flash, then about 5 seconds before the pattern repeats means F6E1. [5]

The user interface is the first named cause. Make sure nothing presses on the buttons.

Start one cycle after the reset and see whether F6E1 returns.
The retailer-copy manual says to call for service if the Clean light or any other light blinks and the dishwasher will not run. [6]
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Two Product Help pages carry it: the “6 Pause 1 Pause” flashing-pattern page and the F6E1 error code page. Both read “User Interface Error, Main Control” and both end by sending you to service if the code remains.
Read the supporting manualIt lists F6E1 among the common codes with the same cause line and explains how a flashing Clean light spells a code: first group is F, second group is E.
Read the supporting manualF6E3 is a suds code: excessive suds, with a clean wash cycle after removing them. F6E1 has no suds step.
Read the supporting manualF1E1 blames the control module; F6E1 names the user interface as well as the main control.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12609 / PH 12609 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12627 / PH 12627 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12628 / PH 12628 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12623 / PH 12623 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-08-31; PH 15083 / PH 15083 (dishwasher)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10401489A (1/12); printed page numbers; retailer copy / printed p11, “Blinking lights” row
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Sources: Product Help PH 12609 and PH 12627, with the F6E3, F1E1 and Reading pages.
The page says user interface error, which includes the panel, but also names the main control.
No. Both pages carry the same line.
F6E1, the same code in the flashing format.
Maytag does not say. If it will not start, book a visit.
Maytag codes, symptoms, parts and service
F1E1 on a Maytag dishwasher is explained as “Potential Cause: Control Module.” Cut the power for 30 seconds, then restore it; schedule a visit if the code is still there.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.